Fujitsu PRIMERGY CX400 M1 System Configurator And Order-Information Manual
  1. Manuals
  2. Brands
  3. Fujitsu Manuals
  4. Server
  5. PRIMERGY CX400 M1
  6. System configurator and order-information manual
Fujitsu PRIMERGY CX400 M1 System Configurator And Order-Information Manual

Fujitsu PRIMERGY CX400 M1 System Configurator And Order-Information Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

PRIMERGY CX400 M1
incl. new CX25y0 M2
System configurator and order-information guide
November 2016
Contents
Instructions
Configuration diagram
Configurator
0
System software
I
CX400 M1 Basic unit
II
III
Processor for CX25y0 M2
IV
V
Graphics/GPGPU/Grid/XeonPhi
VI
VII
Drive Bay for 6x HDD/SSD
VIII
Modular Raid 0/1, Raid5 for 4x 2.5" / 8x 2.5" SAS or SATA HD's.
On-board Controller for 4x 2.5" SATA or SAS HD`s
IX
2.5" SAS / SATA / PCIe Hard disk drives / SATADOM
X
External SAS Disk Array, SAS backup drives or SCSI peripheral devices
XI
Fibre-Channel controller
XII
XIII
XIV
XV
Country specific power cord
PRIMERGY Server
24x 2.5" Hot-plug HDD or SSD (K1530-V100)
12x 2.5" Hot-plug HDD or SSD (K1530-V200)
8x 2.5" Hot-plug HDD or SSD (K1530-V300)

Advertisement

Table of Contents
loading

Related Manuals for Fujitsu PRIMERGY CX400 M1

Summary of Contents for Fujitsu PRIMERGY CX400 M1

  • Page 1: Table Of Contents

    PRIMERGY CX400 M1 incl. new CX25y0 M2 System configurator and order-information guide November 2016 Contents 24x 2.5" Hot-plug HDD or SSD (K1530-V100) 12x 2.5" Hot-plug HDD or SSD (K1530-V200) Instructions Configuration diagram Configurator 8x 2.5" Hot-plug HDD or SSD (K1530-V300)
  • Page 2 Please note that there are information symbols which indicate necessary information. For further information see: http://ts.fujitsu.com/products/standard_servers/index.html (internet) https://partners.ts.fujitsu.com/com/order-supply/configurators/primergy_config/current/Pages/default.aspx (extranet) Prices and availability see price list and PC-/SystemArchitect. Subject to change and errors excepted. Fujitsu Technology Solutions x86 PRIMERGY Server 2 of 33...
  • Page 3 System configurator and order-information guide PRIMERGY CX400 M1 Status 2016-10-31 Configuration diagram PRIMERGY CX400 M1 System unit (I) with up to 24x 2.5" HDD/SSD for CX2550 M1 and up to 12x 2.5" HDD/SSD for CX2570 M1 Below drawing shows slot numbering. For HDD installation order, please refer operating manual.
  • Page 4 2.5"x1" SAS or Slot 1-4: PCIe-3 x16 (low profile, half length) or SATA SATA or PCIe (170mm incl. bracket) right slot from rear view slot1-4@CPU1, slot11-14@CPU2 Key: Included in basic unit =Option Fujitsu Technology Solutions x86 PRIMERGY Server 4 of 33...
  • Page 5 (170mm incl. bracket) left slot from rear view Slot 1-4: PCIe-3 x16 (low profile, half length) (170mm incl. bracket) right slot from rear view slot1-4@CPU1, slot11-14@CPU2 Key: Included in basic unit =Option Fujitsu Technology Solutions x86 PRIMERGY Server 5 of 33...
  • Page 6 2.5"x1" SAS Slot 1-4: PCIe-3 x16 (low profile, half length) or SATA or SATA or PCIe (170mm incl. bracket) right slot from rear view slot1-4/5-8@CPU1, slot11-14/15-18@CPU2 Key: Included in basic unit =Option Fujitsu Technology Solutions x86 PRIMERGY Server 6 of 33...
  • Page 7 - 2x dummy cage for CX2570 M1/M2 variant base unit only - 4x dummy cage for CX25y0 M1/M2 * Nodes (option) - up to 4x CX2550 M1 or M2 - up to 2x CX2570 M1 or M2 Fujitsu Technology Solutions x86 PRIMERGY Server 7 of 33...
  • Page 8 Power code IEC320 C19 -> C14 (200-240V only) S26361-F3151-L350 Power code IEC320 C19 -> C20 S26361-F3151-L300 Power code IEC320 C19 -> US NEMA L6-20p S26361-F3151-L500 S26361-F5558-E50 Liquid cooling tube set for Liquid cooling 1x per CX400 Fujitsu Technology Solutions x86 PRIMERGY Server 8 of 33...
  • Page 9 REGION KIT America For Shipments to EMEA / Asia and For Shipments to Japan regions For Shipments to America region Pacific regions 1x per system 1x per system 1x per system Fujitsu Technology Solutions x86 PRIMERGY Server 9 of 33...

  • Page 10: Cx25Y0 M2 Basic Unit

    * Graphics Controller integrated in iRMC S4 (integrated Remote Management Controller): 1600x1200x16bpp 60Hz, 1280x1024x16bpp 60Hz, 1024x768x32bpp 75Hz, 800x600x32bpp 85Hz, 640x480x32bpp 85Hz (1280x1024x24bpp 60Hz only possible if local monitor or remote video redirection is off) Fujitsu Technology Solutions x86 PRIMERGY Server 10 of 33...
  • Page 11 - ServerView Suite Software package incl. ServerStart, ServerBooks, Management Software and Updates - Documentation engl. (multilingual on CD) Note: Power Cord is not included in the basic unit and has to be configured separately Fujitsu Technology Solutions x86 PRIMERGY Server 11 of 33...
  • Page 12 HDD cage standard HDD cage standard HDD cage standard HDD cage standard max. 4x per system unit max. 1x per CX-Server node max. 4x per system unit max. 1x per CX-Server node Fujitsu Technology Solutions x86 PRIMERGY Server 12 of 33...
  • Page 13 CPU Xeon E5-2630Lv4 10C/20T 1.80GHz 25MB 8.0GT/s 2133MHz 55W S26361-F3933-E131 Xeon E5-2650Lv4 14C/28T 1.70GHz 35MB 9.6GT/s 2400MHz 65W S26361-F3933-E151 For Air cooling S26361-F3849-E100 Cooling Kit 2nd CPU For Liquid cooling Fujitsu Technology Solutions x86 PRIMERGY Server 13 of 33...
  • Page 14 Xeon E5-2630v4 10C/20T 2.20GHz 25MB 8.0GT/s 2133MHz 85W S26361-F3933-L740 Xeon E5-2640v4 10C/20T 2.40GHz 25MB 8.0GT/s 2133MHz 90W S26361-F3933-L750 Xeon E5-2650v4 12C/24T 2.20GHz 30MB 9.6GT/s 2400MHz 105W S26361-F3933-L723 Xeon E5-2623v4 4C/8T 2.60GHz 10MB 8.0GT/s 2133MHz 105W Fujitsu Technology Solutions x86 PRIMERGY Server 14 of 33...

  • Page 15: Memory

    All four modules are active and full capacity can be used. Multiple of 4 identical modules to be configured per CPU Fujitsu Technology Solutions x86 PRIMERGY Server 15 of 33...
  • Page 16 Choose up to 8 order codes per CPU NOT available for Liquid Cooling 32GB (1x32GB) 4Rx4 DDR4-2133 LR ECC S26361-F3844-E617 64GB (1x64GB) 4Rx4 DDR4-2133 LR ECC S26361-F3844-E618 For Liquid Cooling, S26361-F3844-E618 * must be handle as Special Release. Fujitsu Technology Solutions x86 PRIMERGY Server 16 of 33...
  • Page 17 - one DDR4 load reduced ECC memory Module, 1.2V Choose up to 8 order codes per CPU For Liquid Cooling, S26361-F3935-E616 * S26361-F3935-E616 64GB (1x64GB) 4Rx4 DDR4-2400 LR ECC must be handled as Special Release. Fujitsu Technology Solutions x86 PRIMERGY Server 17 of 33...
  • Page 18 4 memory modules connected to Channel A - E on the 1st/2nd CPU (can not be populated by UDIMM or 4R RDIMM memory modules) - See below and next page for a detailed descriptions of the memory configuration supported. Fujitsu Technology Solutions x86 PRIMERGY Server 18 of 33...

  • Page 19: Independent Channel Mode

    XEON CPU Performance Channel Mode requires identical modules on all channels of each Bank per CPU. If this mode is used, a multiple of 4 identical modules has to be ordered. Fujitsu Technology Solutions x86 PRIMERGY Server 19 of 33...
  • Page 20 Riser card for GPGPU is part of delivery no PCIe bracket attached no PCIe bracket attached no PCIe bracket attached no PCIe bracket attached S26361-F2222-L40 S26361-F2222-L80 S26361-F2222-L100 S26361-F2222-Lxxx for loose delivery Riser is part of basic unit CX270 Fujitsu Technology Solutions x86 PRIMERGY Server 20 of 33...
  • Page 21 NVIDIA SUMS License (1year) for ｒｅｎｅｗａｌ. It needs if you need to NVIDIA SUMS License (1year) for ｒｅｎｅｗａｌ. It needs if you need continue SUMs after one year. to continue SUMs after one year. continue SUMs after one year. Fujitsu Technology Solutions x86 PRIMERGY Server 21 of 33...

  • Page 22: Accessible Drives

    External Blu-Ray Drive S26341-F103-L127 as long as available 2) USB Memorybird: MyUSBS A910 8GB, MLC Flash S26391-F6048-L208 as long as available S26391-F6048-L216 as long as available MyUSBS A910 16GB, MLC Flash Fujitsu Technology Solutions x86 PRIMERGY Server 22 of 33...
  • Page 23 RAID Advanced Software Options S26361-F5243-L1 / L2 License Activation Key S26361-F5243-L200 for CacheCade 2.0 and FastPath for 1 Controller S26361-F5243-L660 S26361-F5552-L330 S26361-F5552-L350 (2x cables are required in case of >=4HDDs are installed per node) Fujitsu Technology Solutions x86 PRIMERGY Server 23 of 33...
  • Page 24 *) SSD Mainstream Endurance SSD PCIe Gen3 2.5" with hot plug/hot replace tray 800GB S26361-F5534-E800 xxDWPD over 5y 1.6TB S26361-F5534-E161 2.0TB S26361-F5534-E201 max. 2 per server node w/ Type B drive bay option Fujitsu Technology Solutions x86 PRIMERGY Server 24 of 33...
  • Page 25 Gen3 2.5" with hot plug/hot replace tray PCIe 800GB S26361-F5534-E800 1.6TB S26361-F5534-E161 2.0TB S26361-F5534-E201 *) SSD Mainstream Endurance max. 2 per server node w/ Type B drive bay option xxDWPD over 5y Fujitsu Technology Solutions x86 PRIMERGY Server 25 of 33...
  • Page 26 240GB, for read/write workload (mixed-use) S26361-F5588-E240 3DWPD over 5y SATA 480GB for read/write workload (mixed-use) S26361-F5588-E480 960GB, for read/write workload (mixed-use) S26361-F5588-E960 1.92TB, for read/write workload (mixed-use) S26361-F5588-E192 max. 2 per server node Fujitsu Technology Solutions x86 PRIMERGY Server 26 of 33...
  • Page 27 Only for CX2550 M1 / M2 SAS 12Gb/sec CX2570 M1/M2 does not support int. SAS HBA int: 8 port PCIe 3.0 x8, Loose delivery full height or low profile bracket S26361-F3842-L502 max. 1x per system Fujitsu Technology Solutions x86 PRIMERGY Server 27 of 33...
  • Page 28 Only for CX2550 M1 / M2 SAS 12Gb/sec CX2570 M1/M2 does not support ext. SAS HBA ext: 8 port PCIe 3.0 x8, Loose delivery low profile bracket S26361-F3845-L501 max. 2x per system Fujitsu Technology Solutions x86 PRIMERGY Server 28 of 33...
  • Page 29 PCIe x8, 170mm max. 2x per system max. 1x per system max. 2x per system loose delivery: Dual Channel S26361-F4994-L502 Dual Channel S26361-F5313-L502 Dual Channel S26361-F5580-L502 contains LP and FH brackets. Fujitsu Technology Solutions x86 PRIMERGY Server 29 of 33...

  • Page 30: Communication/Network

    PLAN EP OCe14102 2x 10GBase-T LP 2 port NIC with RDMA, Emulex S26361-F5557-E201 S26361-F5557-L501 10Gb Ethernet controller with SFP+ interface (for SFP+ modules or twinax cables, Fujitsu / Intel based) Eth Ctrl 2x10Gbit PCIe x8 D2755 SFP+ 2 port NIC, Intel 82599 based S26361-F3629-E202...
  • Page 31 S26361-F5549-L563, QSFP, 100Gb, 3m QSFP, 1m, 2m and 3m max. 2x per adapter Copper cable are also available for loose delivery as S26361-F5563-L150, QSFP, 100Gb, 1.5m S26361-F5563-L200, QSFP, 100Gb, 2m S26361-F5563-L300, QSFP, 100Gb, 3m Fujitsu Technology Solutions x86 PRIMERGY Server 31 of 33...

  • Page 32: System Management Products (Remoteview)

    IT administrators to ensure a continuous 24x7 server operation. ServerView embedded Lifecycle Management (eLCM) for Fujitsu PRIMERGY servers greatly supports such routine tasks by consolidating and enhancing management functions directly available (“embedded”) within the server.

  • Page 33: Change Report

    Added comment "for M1 only" 2016-04-05 S26361-F2222-E964 as soon as available 2016-04-01 ATD option for CX25x0 M2 will be available in 04/2016. 2016-04-01 First Release - configurator with CX25y0 M2 2016-06-02 S26361-F5243-E4/L4 added Fujitsu Technology Solutions x86 PRIMERGY Server 33 of 33...

Table of Contents