Fujitsu PRIMERGY CX400 M1 System Configurator And Order-Information Manual page 23

J
Va
Section Chassis Selection
S26361-K1530-V100
S26361-K1530-V200
VI
Section Drive Bay for 6x HDD/SSDs
Type A
S26361-F5519-E10
6x 2.5" HDD/SSD
SAS / SATA only
max. 1x per CX25y0
VII
Section Modular Raid 0/1, Raid5 for 4x / 8x 2.5" SAS or SATA HD`s. On-board Controller for 4x 2.5" SATA or SAS HD`s
On board SATA Controller with 6 Gb/s and up to 6x 2.5" SATA HDDs (no additional controller required)
For SAS HDD/SSD a modular RAID-controllers is required
For Read-Intensive SATA SSDs (*F5525*) a modular RAID-controllers is required
For PCIe SSD, no additional controller required
For SAS / SATA HDD and SSD
Modular Raid 0/1 controller with IME support for SAS/SATA
This RAID controller supports 8 ports on the 4 + 4 internal SAS ports
Onb. SATA Controller
Selectable on BIOS setting
AHCI mode (default) or RAID
(0 / 1)
Solid State Disk, Boot Drive, SATA DOM (SATADOM Port, AHCI)
SSD SATA 6Gb/s DOM, Boot Device, non "hot plug/hot replace"
64GB, MTBF=3Mhrs, Endurance=172 TBW (Seq. write)
128GB, MTBF=3Mhrs, Endurance=345 TBW (Seq. write)
SATADOM is designed for use as a boot drive with the Endurance Spec. above.
Vmware not supported.
max. 1x per system
1x
Solid State Disk, Boot Drive, SATA DOM SLC (SATADOM Port, AHCI)
SSD SATA 6Gb/s DOM SLC, Boot Device, non "hot plug/hot replace"
64GB, SATA DOM SLC
SATADOM SLC is designed for use as a Virtual SAN boot drive.
VMware ESXi 6.0 U2 is only supported.
max. 1x per system
Liquid Cooling is not possible
S26361-F3842-E1
PRAID CP400i
Based on chip LSISAS3008
LSI MegaRAID
no Cache, no BBU
RAID 0, 1m 10, 10E, 5, 50
Support for 3Gb/s, 6Gb/s and 12Gb/s
SATA and SAS hard drives
PCIe 3.0 x8
Low profile ex factory
max. 1x per system
K1
Type B
S26361-F5519-E20
6x 2.5" HDD/SSD
SAS / SATA / PCIe
max. 1x per CX25y0
S26361-F5552-E330
SATA Cable
needed to be ordered 1x
SATA drives <= 4pcs
needed to be ordered 2x
SATA drives > 4pcs
max. 2x per system
S26361-F5523-E64
S26361-F5523-E128
S26361-F5621-E64
S26361-F5243-E1
PRAID EP400i
Based on chip LSISAS3108
LSI MegaRAID
1GB Cache with ECC
RAID 0, 1, 10, 5, 50, 6, 60
No optional FBU
Support for 3Gb/s, 6Gb/s and 12Gb/s
SATA and SAS hard drives
PCIe 3.0 x8
Low / High profile ex factory
max. 1x per system
S26361-F5243-E660
RAID Advanced Software Options
License Activation Key
for CacheCade 2.0 and FastPath
for 1 Controller
K2
Fujitsu Technology Solutions x86 PRIMERGY Server
System configurator and order-information guide
PRIMERGY CX400 M1 Status 2016-10-31
S26361-K1530-V300 see Sheet "2.5" HDD"
S26361-F5519-E50
Dummy HDD cage
(no front HDD/SSD usage)
max. 1x per CX25y0
No loose delivery available (only special release)
Therefore above three types must be selected
for dummy node by special release
Modular Raid 5 controller for SAS/SATA
RAID levels 0, 1, 10, 5, 50, 6 and 60
are supported.
This RAID controller supports 8 HDDs on the
4 + 4 internal SAS ports
*S26361-F5243-E4/L4
S26361-F5243-E2*
PRAID EP420i for SafeStore
PRAID EP420i
supports HDD Encryption available
Based on chip LSISAS3108
on special release
LSI MegaRAID
2GB Cache with ECC
RAID 0, 1, 10, 5, 50, 6, 60
No optional FBU
Support for 3Gb/s, 6Gb/s and 12Gb/s
SATA and SAS hard drives
PCIe 3.0 x8
Low / High profile ex factory
max. 1x per system
Controller supports OOB-RAID including HDD
monitoring. No OOB-HDD cable needed
Loose delivery
S26361-F3842-L501
S26361-F5243-L1 / L2
S26361-F5243-L200
S26361-F5243-L660
S26361-F5552-L330
S26361-F5552-L350
(2x cables are required in case
of >=4HDDs are installed per node)
23 of 33