Panasonic DMR-ES25 Operating Instructions Manual page 15

6
Press [ENTER] to start Plug-in Auto
Tuning.
Set Channels Automatically
Ch. 1
Set Channels Automatically
Proceeding . . .
The unit then proceeds with Auto Clock Setting. The time is
displayed when finished.
Set Clock Automatically
Auto Clock Setting is complete.
4/4/2006 12:15 AM
DST........ .............On
Time Zone ........CST
n When one of the following screen appears
"No channels were found." screen
Set Channels Automatically
No channels were found.
Please check antenna or cable connection.
then...
press ENTER again
After turning off the unit, confirm following and perform
setup again.
• Confirm the antenna cable is firmly connected to RF IN
terminal.
• If you do not set channels on this unit, select "Input" in
step 5.
"Auto Clock Setting is incomplete." screen
Set Clock Automatically
Auto Clock Setting is incomplete.
Press ENTER
to set clock manually.
Press [ENTER] and set clock manually (Ô right).
7
Press [ENTER].
A picture or a blue background screen is displayed.
n If the clock is an hour slower or faster than the
actual time
Select "–1" or "+1" in "Adjust Time Zone" in the Setup menu
(Ô page 17).
The unit configures channels according to the Signal Source (RF IN)
settings (Ô page 42) as follows.
Signal Source
(RF IN)
Antenna
VHF
UHF
Cable TV VHF
CATV LOW BAND
CATV MID/SUPER BAND
CATV HYPER BAND
ULTRA BAND
SPECIAL CATV CHANNEL
Band Channel
2–13
14–69
2–13
95–99
14–36
37–65
66–94
100–125
1
Adding and deleting channels
After channel setting on this unit completed, you can add or delete
channels if necessary channels are not set or unnecessary channels
are set.
1
Press the numbered buttons to select
a channel.
Antenna
e.g., 5: [0] Ô [5]
15: [1] Ô [5]
Cable TV
e.g., 5: [0] Ô [0] Ô [5]
15: [0] Ô [1] Ô [5]
115: [1] Ô [1] Ô [5]
• You can also use [1 2 CH] when you are going to delete a
channel.
2
Press [ADD/DLT].
e.g., The channel is deleted.
Channel 15 Deleted
Restart Plug-in Auto Tuning
(after relocation, for example)
The setting of the clock and channel is cleared when you perform
the procedure below. Scheduled recording settings are also cleared.
1
When the unit is on and stopped
Press and hold [2 CH] and [1 CH] on
the main unit for about five seconds.
The unit turns off.
2
Press [^ DVD POWER].
The language selection screen is displayed.
When "Set Clock Manually" screen is displayed
The "Set Clock Manually" screen is automatically displayed when:
– there is an error while setting the clock automatically.
– you have selected "Input" in step 5 while setting (Ô page 14).
1
Press [w,q] to select the item you
want to change and press [e,r] to
change the setting.
Set Clock Manually
Month Day Year Hour Minute
1 1 2000 12 00
/ / :
SAT
DST Time Zone
Off EST EST
• DST (Daylight Saving Time):
If you select "On", the clock is advanced one hour starting at
2 a.m. on the first Sunday in April and ending at 2 a.m. on
the last Sunday in October.
• Time Zone shows the time difference from Greenwich Mean
Time (GMT).
EST (Eastern Standard Time)
CST (Central Standard Time)
MST (Mountain Standard Time) = GMT –7
PST (Pacific Standard Time)
AST (Alaska Standard Time)
HST (Hawaii Standard Time)
2
Press [ENTER].
A picture or a blue background screen is displayed.
The clock starts.
Unit's display
AM
DST, Time Zone
(Ô below)
= GMT –5
= GMT –6
= GMT –8
= GMT –9
= GMT –10
RQT8327
15