Time Code; Memory Stop Function - Panasonic NV-GS120GN Operating Instructions Manual

Compatibility with S-VHS or VHS Cassettes
Because this Movie Camera employs a digital
system for recording image and sound data, it is
not compatible with conventional S-VHS or VHS
video equipment that employs an analog
recording system.
The size and shape of the Cassettes are also
different.
Compatibility with Output Signals
Because AV signal output from the AV signal
output socket is analog (the same as
conventional video systems), this Movie Camera
can be connected with S-VHS or VHS video or a
TV for playback.
ª Focus
Auto Focus Adjustment
The Auto Focus System automatically moves
forward and backward the focusing lens inside
the Movie Camera to bring the subject into focus
so that the subject can be seen clearly.
However, the Auto Focus System does not
function properly for the following subjects or
under the following recording conditions.
Please use the Manual Focus Mode instead.
1) Recording a subject whose one end is
located closer to the Movie Camera and
the other end farther away from it
≥Because Auto Focus makes adjustments at
the centre of an image, it may be impossible
to focus on a subject that is located in both
foreground and background.
2) Recording a subject behind dirty or dusty
glass
≥Because the focus is on the dirty glass, the
subject behind the glass will not be focused.
3) Recording a subject in dark surroundings
≥Because the light information that comes
through the lens decreases considerably,
the Movie Camera cannot focus correctly.
4) Recording a subject that is surrounded by
objects with glossy surfaces or by highly
reflective objects
≥Because the Movie Camera focuses on the
objects with glossy surfaces or on highly
reflective objects, the recording subject may
become blurry.
5) Recording a fast-moving subject
≥Because the focus lens-inside moves
mechanically, it cannot keep up with the
fast-moving subject.
6) Recording a subject with little contrast
≥Because the Movie Camera achieves focus
based upon the vertical lines of an image, a
subject with little contrast, such as a white
wall, may become blurry.
Others
ª Time Code
Time Code signals are data that indicate time
measured in hours, minutes, seconds, and
frames (25 frames per second). If this data is
included in a recording, an address is assigned to
each image on the tape.
≥The Time Code is automatically recorded as a
part of the sub-code at each recording.
≥When a new (previously unrecorded) Cassette
is inserted, the Time Code automatically starts
from zero. If a recorded Cassette is inserted,
the Time Code picks up from the point where
the last scene was recorded. (In this case, when
the Cassette is inserted, the zero display
[0h00m00s00f] may appear, but the Time Code
starts from the previous value.)
≥The Time Code cannot be reset to zero.
≥Unless the Time Code is continuously recorded
from the beginning of a tape, accurate editing
may not be possible. To ensure that the Time
Code will be recorded with no breaks, we
recommend the use of the Blank Search
Function ( ) before recording a new scene.
-21-
ª Memory Stop Function
The Memory Stop Function is useful for the
following operations.
Rewinding or fast-forwarding a tape to a
desired position
1
Set [DISPLAY] >> [C.DISPLAY] >>
[MEMORY].
2
Reset the Tape Counter to zero at the tape
position from which you want to play it
back later. ( ,
-6-
3
Start playback or recording.
4
After playback or recording has finished:
Set the Movie Camera to Tape Playback
Mode.
5
Rewind the tape.
≥The tape automatically stops approximately
at the position where the counter was set to
zero.
Stopping editing automatically during audio
dubbing
1
Set [DISPLAY] >> [C.DISPLAY] >>
[MEMORY].
2
Reset the Tape Counter to zero at the
position where you want to stop editing.
3
Play back the still picture where you want to
start audio dubbing.
4
Start audio dubbing. (
≥Audio dubbing automatically stops at the
position where the counter was set to zero.
-68-
)
-15-
)
-45-