Advertisement
Dimplex
Model : EvoRad2BTA
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
IMPORTANT: If the appliance is damaged,
check immediately with the supplier before
installation and operation.
This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental capabilities
or lack of experience or knowledge if they
have been given supervision or instruction
concerning the use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be
made by children without supervision.
Children of less than 3 years should be kept
away unless continuously supervised. Children
aged from 3 years and less than 8 years shall
only switch on/off the appliance provided that
it has been placed or installed in its intended
normal operating position and they have been
given supervision or instruction concerning
the use of the appliance in a safe way and
understand the hazards involved. Children
aged from 3 years and less than 8 years shall
not plug in, regulate and clean the appliance
or perform user maintenance.
CAUTION: Some parts of this product can
become very hot and cause burns. Particular
attention has to be given where children and
vulnerable people are present.
This heater carries the warning symbol
indicating that it must not be covered.
DO NOT use the heater in the immediate
surroundings of a bath, a shower or a swimming
pool.
WARNING: This heater must not be used in
a bathroom.
DO NOT place the heater directly below a fixed
socket outlet.
WARNING: In order to avoid overheating, do
not cover the heater.
We recommend that you open a window to
ventilate the room when using the heater for
the first time.
Unplug the heater when not required for long
periods.
IMPORTANT: If the mains lead of this appliance
is damaged, it must be replaced by the
manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard.
DO NOT use the heater where gas, petrol, paint
or other inflammable goods are used or stored.
The heater is designed for operation on an AC electricity supply, and is suitable
for use in domestic dwellings and similar indoor locations.
Always ensure that the appliance is stood on a firm, level base near to, but
not directly beneath, a suitable fixed socket outlet.
The heater is fitted with castors and a handle for ease of movement.
It is supplied with a cord and plug ready for use.
The supply cord should be uncoiled before use (see 'Storage').
DO NOT pull the heater along by the mains lead.
Important - The heater must only be operated with the wheels and castors
fitted and in the upright position as shown in Fig. 1.
Warning – The heater complies with stringent safety standards but to ensure
efficient operation SURFACES OF THE HEATER WILL BECOME HOT
AND CONTACT WITH THESE AREAS SHOULD BE AVOIDED, particularly
between the fins on the top and sides.
Electrical
WARNING – THIS APPLIANCE MUST BE EARTHED
If the socket outlets in your home are not of the 13 amp BS1363 type they
will not accept the plug connected to this heater, therefore cut off the plug.
When cut off this plug can constitute a shock hazard if inserted into a socket
outlet. It must therefore be disposed of safely.
Before wiring the appropriate plug please note that the wires in this mains
lead are coloured in accordance with the following code:
GREEN/YELLOW:
BLUE:
BROWN:
Connect the Green/Yellow wire to the terminal marked E or the earth symbol
or coloured Green or Green/Yellow.
Connect the Brown wire to the terminal marked L or coloured Red.
Connect the Blue wire to the terminal marked N or coloured Black. DO NOT
connect the Brown (Live) or the Blue (Neutral) wires to the Earth terminal of
your 13 amp plug. If the terminals of the plug are unmarked or you are in
any doubt, consult a qualified electrician.
Fitting the Castors
IMPORTANT: The castors should only be fitted to the outer fins (as shown
in Fig. 2). Fitting the castors to any other fin may result in the product
becoming unstable and may topple over during operation.
WARNING: THE HEATER IS HEAVY – TAKE CARE WHEN LIFTING AND
ENSURE THAT IT IS SUPPORTED DURING ASSEMBLY TO PREVENT
IT FROM TOPPLING.
Remove the carton containing the castor assemblies from the packing.
Turn the heater upside down on a carpet or other soft surface to avoid damage
If required request the assistance of a second person. Position a castor bracket
onto the outer fin and secure in place using the screws provided (see Fig. 2).
Repeat the process for the other castor, ensuring it is located on the other
end fin.
Lift the heater clear of the floor, then turn it back upright and stand it on its
castors as shown in Fig. 1. It is now ready for use.
Positioning the Heater
Select the position for the heater ensuring there is clearance from any furniture
and fittings of at least 300mm above the heater and 150mm each side. The
heater should only be operated on a flat stable surface.
Operational modes
The electronic control has four control modes: AUTO, MANUAL, BOOST
and STANDBY mode (see Fig. 4)
In both MANUAL and AUTO mode there are three heat settings options
(see Fig. 5):
'Intelligent' Eco Mode - This is the initial default setting, the convector will
automatically start up in this setting once power is applied. The convector
will automatically regulate the room temperature accordingly. In this mode
the convector operates at full power, however the output of the convector is
automatically reduced and regulated as the room temperature approaches
the desired level. This mode optimises energy use by calculating the most
efficient and effective way to achieve the desired temperature setting. The
desired room temperature can be adjusted at any time during operation by
pressing the appropriate key.
Low Heat - In this option, the appliance will operate at a low heat setting,
the appliance will automatically cycle at this setting to maintain the room
temperature setting.
High Heat - In this option, the appliance will operate at a high heat setting,
the appliance will automatically cycle at this setting to maintain the room
temperature setting.
Press the Mode key,' ', to toggle through the modes and the ENTER key
to confirm the mode selection. Note: when selecting the mode if the ENTER
key is not pressed, after 5 seconds the heater will activate the mode shown
on the LCD display.
Initial Operation
When the heater is initially connected to the mains the heater will power
up in MANUAL mode with a set temperature of 30˚C. The Mains and Heat
indication neon will be lit and the LCD display will be as per Fig.6. For
subsequent operations the unit will power up in its previous state, i.e. if it was
in the boost mode when the unit was plugged out when power is reinstated
it will resume in boost mode.
EARTH
NEUTRAL
LIVE
Advertisement
