Weider WEEVSY49220 User Manual page 11

27. Attach the Backrest (41) to the Front Upright (42)
with two M6 x 73mm Bolts (43) and two M6
Washers (78).
28. Press a 38mm Square Inner Cap (32) into the
end of the Seat Frame (36). Attach the Bumper
(67) to the Seat Frame (36) with the M5 x 20mm
Self-tapping Screw (80).
Insert the M6 x 50mm Carriage Bolt (38) into the
centre hole in the Seat Plate (37). Attach the wide
end of the Seat (13) to the Seat Plate with two
M6 x 16mm Screws (18).
Attach the Seat (13) to the Seat Frame (36) with
the M6 x 50mm Carriage Bolt (38), an M6
Washer (78), and the M6 Nylon Locknut (2).
Attach the other end of the Seat (13) to the Seat
Frame (36) with an M6 x 50mm Bolt (33) and an
M6 Washer (78).
29. Press two 38mm Square Inner Caps (32) into the
ends of the Leg Lever (29).
Lubricate an M10 x 63mm Bolt (90). Attach the
Leg Lever (29) to the Seat Frame (36) with the
Bolt and an M10 Nylon Locknut (21). Do not
overtighten the Nylon Locknut; the Leg Lever
must be able to pivot easily.
30. Slide a Pad Tube (28) into the hole in the Leg
Lever (29). Press two 19mm Round Inner Caps
(34) into the ends of the Pad Tube. Slide two
Foam Pads (30) onto the Pad Tube.
Repeat this step with the other Pad Tube (28)
and the Seat Frame (36).
27
43
78
42
43
78
41
28
13
38
37
36
18
32
78
67
33
2
80
29
90
Lubricate
32
36
21
29
30
30
28
30
29
30
36
30
34 28
34
14
16. Route the High Cable (23) up through the Top
Frame (55), around the 115mm Pulley (74), and
back down through the Top Frame. Attach the
Pulley inside the Top Frame with an M10 x 75mm
Bolt (76), two 17.5mm Spacers (77), two M10
Washers (9), and an M10 Nylon Locknut (21).
17. Attach the High Cable (23) to the "U"-bracket (57)
with an M8 Washer (70) and an M8 Nylon
Locknut (3). Note: Do not completely tighten
the Nylon Locknut; it should be threaded only
two turns onto the end of the Cable, as shown
in the inset drawing.
Attach the "U"-bracket (57) to the Weight Tube
(63) with an M8 x 45mm Bolt (66) and an M8
Nylon Locknut (3). Do not overtighten the
Nylon Locknut; the Weight Tube must be able
to pivot easily.
18. Locate the Low Cable (69), which has a ball on
each end. Rest the Cable in the bracket on the
Base (4). Attach a 90mm Pulley (15) inside the
bracket with an M10 x 45mm Bolt (88) and an
M10 Nylon Locknut (21).
32
19. Wrap the Low Cable (69) around a 90mm Pulley
(15). Attach the Pulley and a pair of Pulley
Covers (40) to the bottom hole in the Front
34 Upright (42) with an M10 x 110mm Bolt (64), an
M10 Washer (9), and an M10 Nylon Locknut (21).
Be sure the large tabs on the Pulley Covers
34
are on the side shown.
16
74
76
77
55
9
77
9
21
23
17
23
70
66
57
3
63
3
18
15
88
4
69
21
19
69
40
15
64
42
Large
40 Tab
9
21
11
23