Onkyo TX SR608 Instruction Manual page 51

Changing the Remote Controller's ID
1
While holding down RECEIVER, press and hold
down SETUP until the remote indicator lights
(about 3 seconds) (➔
2
Use the number buttons to enter ID 1, 2, or 3.
The remote indicator flashes twice.
TUNER
For FM/AM tuning to work properly, you must specify the
FM/AM frequency step used in your area. Note that when
this setting is changed, all radio presets will be deleted.
■
FM/AM Frequency Step (North American and
Taiwan models)
200k/10kHz:
Select if 200 k/10 kHz steps are used in your area.
50k/9kHz:
Select if 50 k/9 kHz steps are used in your area.
■
AM Frequency Step (European, Australian and
Asian models)
10kHz:
Select if 10 kHz steps are used in your area.
9kHz:
Select if 9 kHz steps are used in your area.
SIRIUS Settings (North American models)
See the separate Satellite Radio Guide for more informa-
tion.
■
SAT Radio Mode
If you connect a SIRIUS Satellite Radio antenna to the
AV receiver (sold separately), set this setting to "SIR-
IUS".
■
Antenna Aiming
■
SIRIUS Parental Lock
These items are for use with SIRIUS Satellite Radio.
It's not available if "SAT Radio Mode" is set to
"None".
HDMI
■
Audio TV Out
Off:
HDMI audio is not output.
On:
HDMI audio is output.
This preference determines whether audio received at the
HDMI IN is output by the HDMI OUT. You may want to
turn this preference on if your TV is connected to the
HDMI OUT and you want to listen to the audio from a
component that's connected to an HDMI IN, through your
TV's speakers. Normally, this should be set to "Off".
Note
• If " On " is selected and the audio can be output from the TV, the
AV receiver will output no sound through its speakers. In this
case, "TV Sp On" appears on the display.
" "
• When TV Control is set to
" "
Auto .
38).
" "
On , this setting is fixed to
• With some TVs and input signals, no sound may be output even
when this setting is set to " On
• When the "Audio TV Out" setting is set to
" "
trol" is set to On (➔ 52) and you're listening through your
TV's speakers (➔ 17), if you turn up the AV receiver's volume
control, the sound will be output by the AV receiver's front left
and right speakers. To stop the AV receiver's speakers producing
sound, change the settings, change your TV's settings, or turn
down the AV receiver's volume.
■
Lip Sync
Disable:
HDMI lip sync disabled.
Enable:
HDMI lip sync enabled.
The AV receiver can be set to automatically correct any
delay between the video and the audio, based on the data
from the connected monitor.
Note
• This function works only if your HDMI-compatible TV supports
HDMI Lip Sync.
• You can check the amount of delay being applied by the HDMI
Lip Sync function on the A/V Sync screen.
■
HDMI Control (RIHD)
Off:
p disabled.
On:
p enabled.
This function allows p
connected via HDMI to be controlled with the AV receiver
(➔ 72 to 73).
Note
• When set to "On" and close the menu, the name of connected
p-compatible components and "RIHD On" are dis-
played on the AV receiver.
"Search..." → "(name)" → "RIHD On"
When the AV receiver cannot receive the name of the compo-
nent, it is displayed as "Player
the number of two or more component).
When set to "Off" and close the menu, "RIHD Off" are dis-
played on the AV receiver.
"Disconnect" → "RIHD Off"
• When an p-compatible component is connected to the
AV receiver via the HDMI cable, the name of the connected
component is displayed on the AV receiver display. For example,
while you are watching TV broadcasting, if you operate a
Blu-ray Disc/DVD player (being powered on) by the remote
control of the AV receiver, the name of the Blu-ray Disc/DVD
player is displayed on the AV receiver.
" "
• Set to Off when a connected piece of equipment is not com-
patible or it is unclear whether the equipment is compatible or
not.
• If movement is unnatural when set to
" "
to Off .
• Refer to the connected component's instruction manual for
details.
" (➔ 52).
" " "
On , or TV Con-
-compatible components
* * *
" or "Recorder ", etc (" " means
" On " , change the setting
En
51