Product Warranty - Curtis SERA2B Service Manual

Seraphim coffee brewer

Service manual (24 pages)

User manual (41 pages)

Table of Contents

Wilbur Curtis Co., Inc. certifies that its products are free from defects in material and workmanship under normal use. The following limited warranties

and conditions apply:

years, parts and labor, from original date of purchase on digital control boards

years, parts, from original date of purchase on all other electrical components, fittings and tubing

year, labor, from original date of purchase on all other electrical components, fittings and tubing

Additionally, Wilbur Curtis Co., Inc. warrants its grinding burrs for forty (40) months from the date of purchase or 40,000 pounds of coffee, whichever

comes first. Stainless steel components are warranted for two (2) years from the date of purchase against leaking or pitting. Replacement parts

are warranted for ninety (90) days from the date of purchase or for the remainder of the limited warranty period of the equipment in which the

component is installed.

All in-warranty service calls must have prior authorization. For authorization, call the Technical Support Department at 800-995-0417.

Additional conditions may apply. Go to www.wilburcurtis.com to view the full product warranty information.

CONDITIONS & EXCEPTIONS

The warranty covers original equipment at time of purchase only. Wilbur Curtis Co., Inc., assumes no responsibility for substitute replacement parts

installed on Curtis equipment that have not been purchased from Wilbur Curtis Co., Inc. Wilbur Curtis Co., Inc. will not accept any responsibility if

the following conditions are not met. The warranty does not cover:

•

Adjustments and cleaning: The resetting of safety thermostats and circuit breakers, programming and temperature adjustments are the

responsibility of the equipment owner. The owner is responsible for proper cleaning and regular maintenance of this equipment.

•

Replacement of items subject to normal use and wear: This shall include, but is not limited to, spray heads, light bulbs, shear disks, "O"

rings, gaskets, silicone tubing, canister assemblies, whipper chambers and plates, mixing bowls, agitation assemblies and whipper propellers.

The warranty is void under the following circumstances:

•

Improper operation of equipment: The equipment must be used for its designed and intended purpose and function.

•

Improper installation of equipment: This equipment must be installed by a professional technician and must comply with all local electrical,

mechanical and plumbing codes.

•

Improper voltage: Equipment must be installed at the voltage stated on the serial plate supplied with this equipment.

•

Improper water supply: This includes, but is not limited to, excessive or low water pressure and inadequate or fluctuating water flow rate.

•

Damaged in transit: Equipment damaged in transit is the responsibility of the freight company and a claim should be made with the carrier.

•

Abuse or neglect (including failure to periodically clean or remove lime accumulations): The manufacturer is not responsible for variation

in equipment operation due to excessive lime or local water conditions. The equipment must be maintained according to the manufacturer's

recommendations.

Repairs and/or Replacements are subject to Curtis' decision that the workmanship or parts were faulty and the defects showed up under normal

use. All labor shall be performed during regular working hours. Overtime charges are the responsibility of the owner. Charges incurred by delays,

waiting time, or operating restrictions that hinder the service technician's ability to perform service is the responsibility of the owner of the equipment.

This includes institutional and correctional facilities. Wilbur Curtis Co., Inc. will allow up to 100 miles, round trip, per in-warranty service call.

Return Merchandise Authorization (RMA): All claims under this warranty must be submitted to the Wilbur Curtis Technical Support Department

prior to performing any repair work or return of this equipment to the factory. All returned equipment must be properly re-packaged in the

original carton and received by Curtis within 45 days following the issuance of a RMA. No units will be accepted if they are damaged in

transit due to improper packaging. NO UNITS OR PARTS WILL BE ACCEPTED WITHOUT A RETURN MERCHANDISE AUTHORIZATION

(RMA). THE RMA NUMBER MUST BE MARKED ON THE CARTON OR SHIPPING LABEL. All warranty claims must be submitted within

60 days of service. Invoices will not be processed or accepted without a RMA number. Any defective parts must be returned in order

for warranty invoices to be processed and approved. All in-warranty service calls must be performed by an authorized service agent. Call the

Wilbur Curtis Technical Support Department to find an agent near you.

ECN17296 05/12/16 @ 8.8 rev E