Specifications; Model - Toro 02003 Operator's Manual

Specifications
Briggs & Stratton Daihatsu, diesel, three-
Engine:
cylinder, 4-cycle, overhead valve, water-cooled, 23 hp @
3600 rpm, 850 cc displacement, governed speed of 3200
rpm. Mechanical fuel pump. 3.31 l oil capacity.
The cooling system is filled with a
Cooling System:
50/50 solution of water and permanent ethylene glycol
anti-freeze.
Fuel System: Fuel tank capacity 20 liters. Fuel filter
with water separator. Fuel shut-off valve.
: Eaton model 11 hydrostatic transmission
Traction Drive
integrally coupled to a Peerless model 1310 axle. Travel
speed range is 0–13.5Km/h (0–8.5 mph) forward and 4.8
Km/h reverse (0–3 mph).
: Foot-operated traction pedal. hand-operated
Controls
throttle, ignition switch, PTO switch, lift lever, parking
brake and seat adjustment.
Cutting Drive: Constant-tension belt drive system with
electric clutch utilizing a poly-V belt from the engine to
the jackshaft and BX section V-belt drive from the
jackshaft to each cutting unit.
Two 23 x 8.5-12 front-drive turf tires
Tires and Wheels:
with 4-ply construction. Rear tires for the four-wheel
configuration, 16 x 6.5-6 turf tires with 4-ply
construction. Rear tire for the three-wheel configuration,
18 x 6.5-8 with 4-ply construction.
12-volt, 255 cold cranking amps at
Electrical Features:
180 C, 50-amp reserve capacity at 270 C. Battery, 16-
amp alternator, seat, traction, PTO and parking brake
interlock switches; electrical leads provided for optional
light and hour meter installations.
Pinion and gear sector with solid control link
Steering:
to the rear steer assembly, 2.5 turns lock to lock.
Service braking accomplished through
Brakes:
hydrostatic transmission. Parking brake controls
secondary shaft internal to the axle assembly and is
actuated by a control lever.
Main Frame: All-steel welded construction utilizing
tubular and formed sheet metal sections
Seat: Standard cushion seat and optional deluxe
suspension seat with arm rest and weight adjustment.
The seat is adjustable fore and aft. Arm rest kit also
available.
Category "0" A-Frame mounting system
Lift System:
connected to the tractor via parallel linkage. One double-
acting 60 mm bore, 140-mm stroke hydraulic cylinder
receiving oil from hydrostatic transmission charge pump
via the control valve with float position. Maximum
operating pressure is 6895 kPa. When the traction unit is
equipped with cutting units, all three units are raised and
lowered via the single control lever. The lift system
works with the electric clutch to engage and disengage
the cutting units.
Overall Dimensions and Weight:
Wheel Tread Width
Width across Front Tires
Wheel Base
Overall Length w/ Cutting Units Installed
Overall Height
Tractor Weight
Weight with 5-Blade Fixed Cutting Units
Weight with 8-Blade Floating Cutting Units
Overall Width w/Fixed-Head Units
Overall Width w/Floating Head Units
Transport Width w/Fixed Head Units
Transport Width w/Floating Head Units
Optional Equipment:
Left. 5-Blade Fixed Cutting Unit (2 req.)
Right. 5-Blade Fixed Cutting Unit
Left 8-Blade Floating Cutting Unit (2 req.) Model No. 03437
Right 8-Blade Floating Cutting Unit
Lift Arm Kit, Fixed Cutting Unit
Lift Arm Kit, Floating Cuffing Unit
Rear Axle, 4 Wheel
Full Roller Kit*
Sectional Roller Kit*
Wiehle Roller Kit*
Skid Kit*
Anti-Scalp Roller Kit*
Grass Basket Kit, Floating C.U.
Grass Basket Kit, Fixed C.U.
105.3 cm
132 cm
138.5 cm
229 cm
119 cm
50.4 kg
640 kg
696 kg
195 cm
203 cm
140 cm
200 cm
Model No. 03434
Model No. 03436
Model No. 03439
Model No. 02100
Model No. 02101
Model No. 02201
Model No. 03440
Model No. 03445
Model No. 03450
Model No. 03446
Model No. 03447
Model No. 02302
Model No. 02304
9