Specifications; Battery Disposal(Usa Only) - Sharp MD-MS702MK Service Manual

MD-MS702MK
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER TO
THE OPERATION MANUAL.
General
Power source: DC 3.6 V (rechargeable lithium-ion
DC 5 V (AC adaptor)
AC 120V, 60 Hz
DC 3V:
DC 4.5V: Optionally available car adaptor,
Power consumption: 7 W (AC adaptor)
Output power: RMS; 20 mW (10 mW + 10mW)
(0.2% T.H.D.)
Charging time: Approx. 3.0 hours
(When using the AC adaptor included with
the unit)
Battery life:
When using two,
commerically available,
When using the
high capacity, "AA" size,
rechargeable battery (fully
alkaline batteries (in the
charged) included with the
optionally available
unit
battery case)
Continuous recording:
Continuous recording:
Approx. 4 hours
Approx. 4.5 hours
Continuous play:
Continuous play:
Approx. 6.5 hours Approx. 8 hours
The continuous recording time is for analog inputs when the
volume level is set to "VOL 0".
The continuous play time shows the value when the volume level
is set to "VOL 15".
The above values are the standard values when the unit is
charged and used at an ambient temperature of 68
The operating time when using alkaline batteries may be different,
depending on the type and manufacturer of the batteries, and on
the operating temperature.
Contains nickel cadmium (or sealed lead) battery.Must be
recycled or disposed of properly.Remove the battery from the
product and contact federal or state environmental agencies
for information on recycling and disposal options.

SPECIFICATIONS

battery x 1)
Optionally available battery
case, AD-M70BC
(commercially available, "AA"
size, alkaline battery x 2)
AD-CA20X
(for cars with a 12-24V DC
negative earth electrical system)
When using two, commercially
available, high capacity, "AA"
size batteries with the
rechargeable battery (fully
charged)
Continuous recording:
Approx. 8.5 hours
Continuous play:
Approx. 14.5 hours
o o
F(20 C).
BATTERY DISPOSAL (USA ONLY)
Input sensitivity:
Recording
MIC H
Output level:
Headphones
LINE
Dimensions:
Weight:
Input jack:
Output jack:
MiniDisc Recorder
Type:
Signal readout:
Audio channels:
Frequency response:
Rotation speed:
Error correction:
Coding:
Recording method:
Sampling frequency:
Wow and flutter:
Specifications for this model are subject to change without
prior notice
– 2 –
Reference input
level level impedance
0.25 mV 10 k ohms
MIC L 2.5 mV 10 k ohms
LINE 100 mV 20 k ohms
Specified
Maximum
output output level
— 10 mW +
10 mW
300mV —
(-12dB)
Width: 3-7/16" (87.0 mm)
Height: 1-3/16" (29.4 mm)
Depth: 3-7/32" (81.5 mm)
0.50 lbs.(227 g) with rechargeable battery
Line/optical digital, microphone
(powered by the main unit)
Headphones (impedance: 19 ohms)/
remote control unit
Portable MiniDisc recorder
Non-contact, 3-beam semi-conductor
laser pick-up
Stereo 2 channels/monaural (long-play
mode) 1 channel
20 - 20,000 Hz (± 3 dB)
Approx. 400 - 900 rpm
ACIRC (Advanced Cross Interleave Reed-
Solomon Code)
ATRAC (Adaptive TRansformed
Acoustic Coding), 24-bit computed type
Magnetic modulation overwrite method
44.1 kHz (32 kHz and 48 kHz signals are
converted to 44.1 kHz, and then recorded.)
Unmeasurable
(less than ±0.001% W.peak)
Input
Load
impedance
32 ohms
50 kohms