Steam Delivery; Tips For Using Steam To Froth Milk; Clean The Hot Water/Steam Spout After Use; Customising The Beverages - DeLonghi ECAM65X.55 Instructions For Use Manual

1. Make sure the hot water/steam spout (C6) is attached cor-
rectly to the hot water/steam connection nozzle (A9);
2. Place a container under the spout (as close as possible to
avoid splashes);
3. Press the selection arrow (B2) corresponding to the "
(B3) to enter the menu;
4. Press the selection arrow (B2) corresponding to the
"NEXT>" symbol to display "HOT WATER";
5. Press the selection arrow corresponding to "HOT WATER".
The corresponding image appears on the display (B1),
together with a progress bar which fills gradually as prepa-
ration proceeds;
6. The machine delivers about 250 ml of hot water, then
delivery stops automatically. To interrupt hot water deliv-
ery manually, press the selection arrow corresponding to
"STOP " icon again.
Please note!
• If "Energy Saving" mode is active, you may have to wait a
few seconds before the hot water is delivered.
• Preparation of each coffee can be customised (see sections
"13. Customising the beverages" and "14. Memorising your
personal profile").
12.

STEAM DELIVERY

Important! Danger of burns.
Do not leave the appliance unattended while steam is being
delivered.
1. Make sure the hot water/steam spout (C6) is attached cor-
rectly to the hot water/steam connection nozzle (A9);
2. Fill a container with the liquid to be heated or frothed and
immerse the hot water/steam spout in the liquid;
3. Press the selection arrow (B2) corresponding to the "
symbol (B3) to enter the menu;
4. Press the selection arrow (B2) corresponding to the
"NEXT>" symbol to display "STEAM";
5. Press the selection arrow corresponding to "STEAM". The
corresponding image appears on the display (B1), togeth-
er with a progress bar which fills gradually as preparation
proceeds and after a few seconds, steam to heat the liquid
is delivered from the cappuccino maker;
6. When the required temperature is obtained, interrupt
steam delivery by pressing the "STOP
not deliver steam for more than 3 minutes at a time).
Important!
Always stop steam delivery before extracting the container con-
taining the liquid to avoid burns from splashes.
If "Energy Saving" mode is active, you may have to wait a few
seconds before the hot water is delivered.
"

12.1 Tips for using steam to froth milk

•
•
•
•

12.2 Clean the hot water/steam spout after use

Always clean the hot water/steam spout (C6) after use to avoid
the build-up of milk residues and prevent it from clogging.
1. Place a container under the hot water/steam spout and de-
2. Wait a few minutes for the hot water/steam spout to cool
3. Also remove the steam connection nozzle by pulling it
4. Check the hole in the connection nozzle is not blocked. If
5. Wash all parts of the spout thoroughly with a sponge and
6. Insert the nozzle and cappuccino maker on the connection
"
13.
The aroma and quantity of the beverages can be customised.
1. Make sure the profile (B4) including the beverage you
2. From the homepage, press the selection arrow (B2) corre-
3. Select the beverage you want to customise (a directly
" icon. (You should
4. "CHOOSE COFFEE AROMA": Select the required aroma by
17
Please note!
When choosing the size of the container, bear in mind that
the liquid doubles or triples in volume.
For a richer denser froth, use skimmed or partially skimmed
milk at refrigerator temperature (about 5°C).
For a creamier froth, rotate the container with slow move-
ments in an upward direction.
To avoid milk with poor froth or large bubbles, always clean
the spout (C6) as described in the following section.
liver a little water (see section "11. Delivering hot water").
To interrupt hot water delivery manually, press the selection
arrow corresponding to "STOP
down, then extract (fig. 17) by pressing the release button
(C7). Hold the spout with one hand and with the other,
turn the cappuccino maker and pull it downwards (fig. 23).
downwards (fig. 24).
necessary, clean using a toothpick.
warm water.
nozzle by pushing them upwards and turning them clock-
wise until they are attached.

CUSTOMISING THE BEVERAGES

want to customise is active;
sponding to (B6);
selected beverage or from the beverages selection menu
- B3) to enter the customising screen;
pressing the selection arrows corresponding to "-" or "+"
and press the selection arrow corresponding to "OK
".
" ;