Bosch PWS 700 Original Instructions Manual page 22

OBJ_BUCH-1824-003.book Page 22 Friday, December 12, 2014 11:06 AM
22 | English
Angle Grinder PWS ...
Weight according to
EPTA-Procedure
01/2003 with standard-
auxiliary handle
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Angle Grinder PWS ...
Article number 3 603 ...
Rated power input
Rated speed min
Grinding disc diameter,
max. mm
Thread of grinder spindle
Thread length (max.) of
grinder spindle mm
Weight according to
EPTA-Procedure
01/2003 with standard-
auxiliary handle
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-3.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 12.12.2014
Assembly
Mounting the Protective Devices
 Before any work on the machine itself, pull the mains
plug.
Note: After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales
service agent for maintenance. For addresses, see section
"After-sales Service and Application Service".
1 609 92A 0RY | (12.12.14)
700-115 720-115 730-115
kg 1.8 1.8
/II /II
780-125 7800
CA2 7.. CA2 7..
W 780
-1
12000 12000
125
M 14 M 14
21
kg 1.8
/II
Protection Guard for Grinding
of the work process. For this, press the release lever 1 up-
ward and turn the protection guard 6 to the required position.
 Always adjust the protection guard 6 in such a manner
 Adjust the protection guard 6 in such a manner that
 The protection guard 6 may be turned only upon actua-
Note: The encoding keys on the protection guard 6 ensure
that only a protection guard that fits the machine type can be
mounted.
750-115 750-125
1.8 1.8 1.8
/II /II /II
850-115 850-125
CA2 7.. CA2 7..
780 850
12000 12000
125 115
M 14
21 21
1.8 1.8
/II /II
Place the protection guard 6 onto
the spindle collar of the machine
until the encoding keys of the pro-
tection guard agree with the spin-
dle collar. Press and hold the re-
lease lever 1 while doing this.
Press the protection guard 6 onto
the spindle collar until the shoul-
der of the protection guard is
seated against the flange of the
machine, and turn the protection
guard until it can clearly be heard
to engage.
Adjust the position of the protec-
tion guard 6 to the requirements
that all 3 red cams of release lever 1 engage into the
corresponding notches of the protection guard 6.
sparking is prevented in the direction of the operator.
tion of the release lever 1! Otherwise the power tool
may not continue to be used under any circumstances
and must be taken to an after-sales service agent.
75-115 7500
1.8 1.8
/II /II
8000
CA2 7..
850 800
12000
125 125
M 14 M 14
21 21
1.8 1.8
/II /II
Bosch Power Tools