Improving Foot Pod Calibration - Garmin D2 BRAVO Owner's Manual

appears on your device. Approximately five hours of battery life
remain.

Improving Foot Pod Calibration

Before you can calibrate your device, you must acquire GPS
signals and pair your device with the foot pod
Sensors, page 22).
The foot pod is self-calibrating, but you can improve the
accuracy of the speed and distance data with a few outdoor runs
using GPS.
1
Stand outside for 5 minutes with a clear view of the sky.
2
Start a running activity.
3
Run on a track without stopping for 10 minutes.
4
Stop your activity, and save it.
Based on the recorded data, the foot pod calibration value
changes, if necessary. You should not need to calibrate the
foot pod again unless your running style changes.
Calibrating Your Foot Pod Manually
Before you can calibrate your device, you must pair your device
with the foot pod sensor (Pairing ANT+ Sensors, page
Manual calibration is recommended if you know your calibration
factor. If you have calibrated a foot pod with another Garmin
product, you may know your calibration factor.
1
Hold UP.
2
Select Settings > Sensors.
3
Select your foot pod.
4
Select Cal. Factor > Set Value.
5
Adjust the calibration factor:
• Increase the calibration factor if your distance is too low.
• Decrease the calibration factor if your distance is too high.
Setting Foot Pod Speed and Distance
Before you can customize the foot pod speed and distance, you
must pair your device with the foot pod sensor
Sensors, page 22).
You can set your device to calculate pace and distance from
your foot pod data instead of GPS data.
1
Hold UP.
2
Select Settings > Sensors.
3
Select your foot pod.
4
Select Speed.
5
Select an option:
• Select Indoor when you are training with GPS turned off,
usually indoors.
• Select Always to use your foot pod data regardless of the
GPS setting.
tempe
The tempe is an ANT+ wireless temperature sensor. You can
attach the sensor to a secure strap or loop where it is exposed
to ambient air, and therefore, provides a consistent source of
accurate temperature data. You must pair the tempe with your
device to display temperature data from the tempe.
Device Information
Contacting Garmin Aviation Product Support
• Go to fly.garmin.com/support
information.
• In the Americas, call (866) 739-5687.
• In Europe, Africa, and the Middle East, call
+44 (0) 37 0850 1243.
Device Information
(Pairing ANT+
22).
(Pairing ANT+
for in-country support
• In Asia Pacific and Australia, call +65 6348 0378.
Viewing Device Information
You can view the unit ID, software version, regulatory
information, and license agreement.
1 Hold UP.
2 Select Settings > System > About.
Specifications
Battery type Rechargeable, built-in lithium-ion battery
Battery life Up to 6 wk.
Water rating 10 ATM*
Operating temperature From -20º to 55ºC (from -4º to 131ºF)
range
Charging temperature From 0º to 45ºC (from 32º to 113ºF)
range
Radio frequency 2.4 GHz
Radio protocols ANT+ wireless technology, Wi‑Fi, Bluetooth
Smart device
*The device withstands pressure equivalent to a depth of 100 m.
For more information, go to www.garmin.com/waterrating.
Battery Information
The actual battery life depends on the features enabled on your
device, such as activity tracking, smartphone notifications, GPS,
internal sensors, and connected ANT+ sensors.
Battery Life Mode
Up to 20 hr. Normal GPS mode
Up to 50 hr. UltraTrac GPS mode with two-minute polling interval
Up to 6 wk. Watch mode
HRM-Run Specifications
Battery type User-replaceable CR2032, 3 V
Battery life 1 yr. (approximately 1 hr./day)
Operating temperature From -10° to 50°C (from 14° to 122°F)
range
Radio frequency/protocol 2.4 GHz ANT+ wireless communications
protocol
Water rating 5 ATM*
*The device withstands pressure equivalent to a depth of 50 m.
For more information, go to www.garmin.com/waterrating.
Data Management
NOTE: The device is not compatible with Windows
Windows NT , and Mac OS 10.3 and earlier.
® ®
Disconnecting the USB Cable
If your device is connected to your computer as a removable
drive or volume, you must safely disconnect your device from
your computer to avoid data loss. If your device is connected to
your Windows computer as a portable device, it is not necessary
to safely disconnect.
1 Complete an action:
• For Windows computers, select the Safely Remove
Hardware icon in the system tray, and select your device.
• For Mac computers, drag the volume icon to the trash.
2 Disconnect the cable from your computer.
Deleting Files
If you do not know the purpose of a file, do not delete it. Your
device memory contains important system files that should not
be deleted.
® 95, 98, Me,
NOTICE
23