Starting The Charge / Discharge Process - GRAUPNER ULTRA TRIO PLUS 16 Operating Manual

10. Starting the charge / discharge process Output 1
3 sec.
L i P o m a n u a l
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
2 sek.
L P - C 5 . 0 A 3 0 0 0 m A h
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
2 sec.
START
* * I N F O R M A T I O N * * *
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
B A L A N C E R C O N .
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
2 sec.
START
B A T T E R Y C H E C K
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
W A I T P L E A S E . . .
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
2 sec.
L P + 2 . 5 0 A 1 4 . 0 1 7 V
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
34
For charging / discharging, or conditioning a pack, select the
desired program as described below, and then set suitable
values.
If the battery does have a balancer connector, connect the
balancer connector to the balancer input (BALANCER CON-
NECTOR) of the charger.
Make sure for the right polarity.
From right handed to left side:
Pin 1 (GND): Ground = battery -,
Pin 2 (1): + cell 1, Pin 3 (2): + cell 2, Pin 4 (3): + cell 3,
Pin 5 (4): + cell 4, Pin 6 (5): + cell 5, Pin 7 (6): + cell 6,
Pin 8 (7): + cell 7, Pin 9 (8): + cell 8
Connect the two pole power charging cable of the battery to the
charger output - BATTERY + with the right polarity.
Hold the START button pressed in for about two seconds, and
the charger display, if the balancer connector is connected or
not. With connected balancer connector the single cell voltages
can be displayed, see 16.
* * I N F O R M A T I O N * * *
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
B A L A N C E R N O T
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
2 sec.
B A T T E R Y C H E C K
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
W A I T P L E A S E . . .
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
If a Li-battery is connected and the balancer
connector is not connected, the charger
2 sec.
will display the cell count of the Lithium
pack, which must be corrected manually,
if it is wrong..
T y p e O U T P U T[ 1 ]
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
L i P o = 3 c e l l s
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
+
-
INC
DEC
START
Press the START button again, and
the charger will assess the battery.
You can interrupt the charge process at any time with another
short press on the START button.
Note: if you interrupt the charge process by pressing the
START button, all display parameters are irretrievably
erased.
C O N
! Caution ! Please take
great care to set the
correct cell count. and
the right battery type.
If you make a mistake,
the battery could
explode and burst into
fl ames !