Operation; Programming The Thermostat Controller; Enabling Override Schedule; Resuming The Programmed Schedule - Johnson Controls TEC2004-4 Installation Instructions Manual

Operation

Programming the Thermostat Controller

After configuring the thermostat controller by means of
the Installer Configuration Menu, program its operating
parameters by means of the Main User Menu. Access
this menu by pressing the MENU key during normal
operation. The Main User Menu contains the basic
operating features of the thermostat controller.
The Main User Menu also uses Auto Help, which is
displayed automatically in the menu when there is a
pause in programming activity. To exit Auto Help,
continue with the programming selection. When the
thermostat controller is in the Main User Menu and is
left unattended for 45 seconds, the menu reverts to the
Status Display Menu.

Enabling Override Schedule

Note: The Override Schedule prompt only appears
when the thermostat controller is in the Unoccupied
Mode.
This menu selection gives the user the option of
overriding the unoccupied setpoints with the occupied
setpoints for the amount of time specified under the
TOccTime parameter. See Table 3.
Note: If one of the digital inputs is configured to
operate as a remote override contact, this menu is
disabled.
To override the unoccupied state while in the Main User
Menu:
1. Press the NO key to all prompts until the Override
Schedule prompt appears. If the thermostat
controller is in the unoccupied state, this is the first
prompt.
2. Press the YES key to enable the temporary
override. The thermostat controller returns to the
Status Display Menu.
When scrolling through the Status Display Menu,
Override now appears for the schedule status
parameter.

Resuming the Programmed Schedule

This menu only appears when the thermostat controller
is in the override mode.
To resume the schedule while in the Main User Menu:
1. Press the NO key to all prompts until the Resume
Schedule prompt appears. If the thermostat
controller is in the override state, this is the first
prompt.
2. Press the YES key to resume the programmed
schedule.
TEC2004-4 and TEC2004-4+PIR Multi-Stage Economizer Wireless Thermostat Controller
The thermostat controller returns to the Status Display
Menu.

Entering Permanent Temperature Setpoints

The first prompt appearing in the Main User Menu of
the thermostat controller when in the occupied state is
to set the permanent temperature setpoint. Permanent
setpoints are stored in the programmed schedule.
To enter the permanent heating and cooling setpoints
for the Occupied and Unoccupied Modes, follow the
steps in Table 4. When changing the temperatures,
press the keys once to change the temperature in
0.5C°/0.5F° increments; press and hold down the keys
to change the temperature in 5.0F°/5.0C° increments.
Table 4: Entering Permanent Temperature
Setpoints (Part 1 of 2)
Thermostat Description
Controller
Display
Press the MENU key while in the
Status Display Menu to enter the
RoomTemp
Main User Menu.
75.0°F
Press the NO key to all prompts until
the temperature setpoint prompt
Temperat
appears on the display (it may be the
set? Y/N
first prompt). Press the YES key to
enter the temperature setting menu.
Press the YES key to change the
occupied cooling setpoint. Press the
Cooling
NO key to advance to the occupied
set? Y/N
heating setpoint menu.
Press the UP/DOWN arrow keys to
set the temperature. Press the YES
Cooling
key to store the value and advance to
75.0°F
the next menu.
Press the YES key to change the
occupied heating setpoint. Press the
Heating
NO key to advance to the unoccupied
set? Y/N
cooling setpoint menu.
Press the UP/DOWN arrow keys to
set the temperature. Press the YES
Heating
key to store the value and advance to
68.0 ° F
the next menu.
Press the YES key to change the
unoccupied cooling setpoint. Press
Unocc CL
the NO key to advance to the
set? Y/N
unoccupied heating setpoint.
Installation Instructions
13