Control Switch Block (Fk5000) - Sony DCR-PC330 Service Manual

[SERVICE POSITION TO CHECK THE VTR SECTION]
Connection to Check the VTR Section
To check the VTR section, set the VTR to the "Forced VTR power ON" mode.
Operate the VTR functions using the adjustment remote commander (with the HOLD switch set in the OFF position).
Setting the "Forced VTR Power ON" mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 02, and press
the PAUSE button of the adjustment remote commander.
Note1: When the flash error code (E: 91: **) is displayed. After completion of "VTR check",
clear the error flag in the following method.
1) Select page: 0, address: 10, and set data: 00.
2) Select page: 7, address: 00, and set data: 80.
3) Select page: 7, address: 01, set data: 80 and press the PAUSE button.
4) Check that the data of page: 7, address: 02 is "01".
BJ-005 board
DC IN jack
AC power
AC IN
adaptor
VC-325 board
CPC-6 flexible jig
(J-6082-370-C)
To eject a cassette, connect
the control switch block
(PS5000).
CPC-6 jig
(J-6082-371-A)
PROCEDURE OF REMOVING THE MECHANISM DECK.
(VTR CHECK SERVICE POSITION)
1 2-2. CABINET (F) SECTION ...................................
2 2-3. CABINET (REAR) SECTION ...........................
3 2-5. CABINET (R) SECTION ..................................
4 2-6. TRIPOD SCREW .............................................
5 2-7. BJ-005 BOARD ................................................
6 2-14. EVF SECTION ...............................................
7 2-16. STROBOSCOPE SECTION ..........................
CN2502
CN2501
CN2503
19 CN1007
20
1
2
CN1008
CN1005
CN1006
CN1501
(CPC)
(page 2-3)
(page 2-3)
(page 2-4)
(page 2-5)
(page 2-5)
(page 2-11)
(page 2-13)
Exiting the "Forced VTR Power ON" mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 00, and press the
PAUSE button of the adjustment remote commander.
4) Select page: 0, address: 01, and set data: 00.
Note2: If the power can not be turned on, after
removing the LCD block. Connect a jumper
wire between Pins 5 (LCD 2.8V) and qg
(BL CONT) of CN1005 on BJ-005 board.
Lens section
CD-452 board
Mechanism deck
CN1801
Control switch block
(PS5000)
Cabinet (rear) section
8 2-20. LENS SECTION ...........................................
9 2-21. FP-706 BOARD - (1) ....................................
0 2-26. VC-325 BOARD ...........................................
qa 2-27. MECHANISM DECK ....................................
qs 2-28. AV-081 BOARD ............................................
qd 2-29. JK-257 BOARD ............................................
2-21
DCR-PC330/PC330E
15
1
5 20
CN1005
Monitor TV
AV-081 board
LANC jack
EVF section
VF-158 board
JK-257 board
Adjustment remote
commander (RM-95)
(page 2-15)
(page 2-15)
(page 2-19)
(page 2-19)
(page 2-20)
(page 2-20)