Siemens SINUMERIK 840C Installation Manual page 29

01.99
MD No. 7 6
5021
1)
NC-Ready
Consid. SW
signal delay by
limit switch
5022
1 Ipo cycle
Emergency
with PLC
1)
retract. (from
failure or 5 V
undervoltage SW 6)
(from SW 6.3)
5024
Reload
Endlessly
workpiece at
5025
turning
POWER ON
rotary axis
(SW2+)
5026
5027
5028
5029
CSB input 7 CSB input 6
5030
signal from signal from
from
UPS: power UPS: power
SW 6.3
failure failure
5038
5039
5040
5041
5042
5043
5044
5051
F62 pro- Progr. predec.
5052
with G171/172
gramming
(from SW 5)
(from SW 6.3)
5053
5060
5061
5062
5063
5064
5065
5066
5067
5068
5069
1) SW 4 and higher
2) SW 5 and higher
3) SW 6 and higher
© Siemens AG 1992 All Rights Reserved
SINUMERIK 840C (IA)
Bit No.
5 4
Neutral pos. Neutral pos.
of outputs f. of outputs f.
mode gr. 6 mode gr. 5
5 V under- Retract when
voltage PLC failure
(from (from
SW 6.3) SW 6.3)
"Alarm" axis
not in C axis
mode (from
SW 5)
CSB input 5 CSB input 4
signal from signal from
UPS: power UPS: power
failure failure
Bits for menu selection
Bits for menu selection
Bits for menu selection
Bits for menu selection
Bits for menu selection
Channel number of the transformation (1st transformation block)
G function for transformation selection (1st transformation block)
1st fictitious axis (1st transformation block)
2nd fictitious axis (1st transformation block)
3rd fictitious axis (1st transformation block)
1st real axis (1st transformation block)
2nd real axis (1st transformation block)
3rd real axis (1st transformation block)
4th real axis (1st transformation block)
5th real axis (1st transformation block)
6FC5197- AA60
1 NC/Drive Machine Data
3 2 1
Neutral pos. Neutral pos. Neutral pos.
of outputs f. of outputs f. of outputs f.
mode gr. 4 mode gr. 3 mode gr. 2
Extended
stopping
Autom. bl. end
value synchr.
G105/G119
Travel thru Extended Axis-specific
transform. threading G function to
2)
centre package PLC 1)
2nd MCS 2nd MCS
mirroring Z 3) mirroring Y 3)
3rd MCS 3rd MCS
mirroring Z 3) mirroring Y 3)
4th MCS 4th MCS
mirroring Z 3) mirroring Y 3)
CSB input 3 CSB input 2 CSB input 1
signal from signal from signal from
UPS: power UPS: power UPS: power
failure failure failure
1)
1)
1)
1)
1)
Cylinder
interpol. with
4 axes (SW 6)
Display of
axes for all
mode groups
(from SW 6)
1.5 General bits
0
Neutral pos.
of outputs f.
mode gr. 1
Stopping
also on
Emerg. OFF
Abort on
contour vio-
lation CRC
2nd MCS
mirroring X 3)
3rd MCS
mirroring X 3)
4th MCS
mirroring X 3)
Dynamic SW
limit switch
Following
3)
axes
CSB input 0
signal from
UPS: power
failure
Declaration
of PLC (up
to SW 3)
Display PLC
config. (up
to SW 3)
Cycle
setting data
No automat.
gen. of
G68 2)
Channel-spec.
axis a. spindle
display 2)
1–19