Related Manuals for Siemens SISTORE AX
Summary of Contents for Siemens SISTORE AX
-
Page 1: Installation Instructions
SISTORE AX Hard Disk Kit (SATA) Installation Instructions Building Technologies Fire Safety & Security Products... - Page 2 Copyright 2007 © Siemens Fire & Security Products GmbH & Co. oHG. All rights reserved. Siemens Fire & Security Products GmbH & Co. oHG confers upon the purchaser the right to use the software. It is not permitted to reproduce this manual in whole or in part or translate it into...
-
Page 3: Table Of Contents
Directives and standards ..............10 Overview SISTORE AX devices ............11 SISTORE AX4 Lite V2.0 .................11 SISTORE AX8/AX16 250/100 V2.8 ............11 SISTORE AX8/AX16 500/200 V3.6 ............12 SISTORE AX HDD extension kit (SATA)..........12 Technical check ..................13 Verification of primary HDD ..............13 5.1.1 Config issues?..................14 5.1.2... -
Page 5: Introduction
Appendices IMPORTANT HDDs in SISTORE AX shall only be installed by qualified service personnel. This document covers the fitting of SATA hard drives into SISTORE AX devices based on SATA HDD technology. SATA HDDs are not compatible with previous IMPORTANT versions of SISTORE AX based on IDE (PATA) HDD technology. -
Page 6: Safety
Do not carry two or more HDDs with one stacked on top of another. Do not let HDDs bump against each other. Do not leave the HDD in a vertical position without putting it in a container. Siemens Building Technologies Fire Safety & Security Products 03.2009... -
Page 7: Setup
Make sure the device is permanently connected to the electricity supply; a readily accessible disconnect device must be provided. Liability claim For reasons of electromagnetic compatibility RS232, USB, audio in/out and power supply cables must not exceed 3 meters length. Siemens Building Technologies Fire Safety & Security Products 03.2009... -
Page 8: Installation
Danger of electrical shock while cleaning the device Disconnect the device from the mains supply before cleaning it. Do not use liquid cleaners or sprays that contain alcohol, spirit or ammonia. Siemens Building Technologies Fire Safety & Security Products 03.2009... -
Page 9: Meaning Of The Written Warning Notices
The severity of a hazard is indicated by the following written warning notices. Signal word Type of risk IMPORTANT Malfunctioning may result. Meanings of the hazard symbols The nature of the hazard is indicated by icons. Warning of a hazard! Siemens Building Technologies Fire Safety & Security Products 03.2009... -
Page 10: Directives And Standards
Directives and standards This product complies with the requirements of the following European directives. The EU declaration of conformity is available to the responsible agencies at: Siemens Building Technologies Fire & Security Products GmbH & Co. oHG 76181 Karlsruhe Germany European Directive 2004/108/EC ”Electromagnetic Compatibility”... -
Page 11: Overview Sistore Ax Devices
Overview SISTORE AX devices Overview SISTORE AX devices This chapter shows the various SISTORE AX models including the scope of delivery of devices ex factory and in the Replacement Pool. SISTORE AX4 Lite V2.0 Product Name Ordering number Def. HDD Ext. -
Page 12: Sistore Ax8/Ax16 500/200 V3.6
Assembly screws and guide rails (for SISTORE AX8/AX16 250/100 and SISTORE AX8/AX16 500/200) Cable ties (2x) SATA HDD kits are not compatible with previous versions of SISTORE AX IMPORTANT based on IDE (PATA) HDDs. Likewise the IDE HDD kits cannot be fitted into SISTORE AX models based on SATA HDD technology. -
Page 13: Technical Check
Technical check This chapter describes the procedures for the technical verification of defective SISTORE AX devices. Please note that the procedures described below can only give an indication of unit condition and the recommended action to be taken. Verification of primary HDD... -
Page 14: Config Issues
Warning message (e.g. “WARNING: Immediately check storage”). Initializing message without proper booting and hang-up of the system. 5.1.4 Booting without HDD? Remove the power supply cable of the HDD and verify if it is working properly. Siemens Building Technologies Fire Safety & Security Products 03.2009... -
Page 15: Verification Of Secondary Hdd
Verify status of HDD in the Storage menu Is it possible to call the SMART menu? 5.2.2 Booting without HDD? Remove secondary HDD from the device and verify if the device is working properly Siemens Building Technologies Fire Safety & Security Products 03.2009... -
Page 16: Installation And Replacement Of Hard Disk Drives
Installation and replacement of hard disk drives This chapter describes the procedures to replace faulty HDDs and install extensions HDDs in the SISTORE AX. Independent of the AX model, in either case the HDD shall be replaced by the standard HDD model (currently Hitachi 250 GB). - Page 17 NOTE The Flat cable between front board and main board should be placed as it was. It needs to be placed on the HDD bracket as displayed in the image. Siemens Building Technologies Fire Safety & Security Products 03.2009...
- Page 18 Installation and replacement of hard disk drives Now close the SISTORE AX by re-installing the top cover. Secure the cover in place by re-inserting and tightening the previously removed cover screws. You can now start up the SISTORE AX. The new hard disk capacity will be displayed in the OSD menu "Storage"...
-
Page 19: Replacement Of The Primary Hdd In Sistore Ax8/Ax16 250/100 V2.8
(3) and on both sides of the SISTORE AX (8). 3. Lift up the housing cover at the rear of the SISTORE AX, and lift it off. 4. Remove the hard disk frame with the primary HDD by loosening the two screws –... - Page 20 8. Secure the hard disk frame including the hard disk unit in the SISTORE using the two screws. 9. Now close the SISTORE AX with the cover, and secure this by inserting and tightening the previously removed screws.
- Page 21 OSD menu "Storage information". Before you can start recording data, the use needs to be defined and the hard disk to be formatted (see SISTORE AX8/AX16 250/100 User Manual). Siemens Building Technologies Fire Safety & Security Products 03.2009...
-
Page 22: Installation Of The Extension Hdd In Sistore Ax8/Ax16 250/100 V2.8
(3) and on both sides of the SISTORE AX (8). 3. Lift up the housing cover at the rear of the SISTORE AX, and lift it off. The empty locations for the hard disk units are then visible. - Page 23 HDD: 5. Fit the hard disk unit into the frame, and secure using the four supplied screws (among accessories enclosed with the SISTORE AX). 6. Ensure the copper grounding strap is installed as per the master HDD. Refer to photo.
- Page 24 1 x power supply (cable tie need to be opened before), 1 x data to the hard disk unit. 10. Now close the SISTORE AX with the cover, and secure this by inserting and tightening the previously removed screws. You can now start up the SISTORE AX.
-
Page 25: Replacement Of The Primary Hdd In Sistore Ax8/Ax16 500/200 V3.6
1. First shutdown the device and disconnect from the power supply. 2. Remove the eleven screws on both sides and at the rear of SISTORE AX. See picture. 3. Lift up the housing cover at the rear of the SISTORE AX, and lift it off. The location for the hard disk unit is then visible –... - Page 26 (as marked in the picture). 8. Fasten the housing cover using the previously removed screws. 9. Start up the device. Please refer to the instruction manual for SISTORE AX. Siemens Building Technologies Fire Safety & Security Products 03.2009...
- Page 27 Installation and replacement of hard disk drives NOTE In order for the additional hard disk unit to be addressed by the SISTORE AX application software, it must be identified as an additional data disk in the „System“ configuration menu and be formatted The new hard disk capacity will be displayed in the OSD menu "Storage...
-
Page 28: Installation Of The Extension Hdd In Sistore Ax8/Ax16 500/200 V3.6
1. First shutdown the device and disconnect from the power supply. 2. Remove the eleven screws on both sides and at the rear of SISTORE AX. See picture. 3. Lift up the housing cover at the rear of the SISTORE AX, and lift it off. -
Page 29: Installation Of The 1
3. Now connect the data line as well as the power supply line to both hard disks (cable tie needs to be open). Note: When inserting the cooling frame make sure the cables are not crushed or damaged. Siemens Building Technologies Fire Safety & Security Products 03.2009... - Page 30 SISTORE AX. NOTE In order for the additional hard disk unit to be addressed by the SISTORE AX application software, it must be identified as an additional data disk in the „System“ configuration menu and be formatted The new hard disk capacity will be displayed in the OSD menu "Storage...
-
Page 31: Installation Of The 2Nd Additional Hard Disk Underneath The Cd/Dvd Drive
3. Attach the two guide rails to the hard disk unit using the four screws provided for this purpose. Siemens Building Technologies Fire Safety & Security Products 03.2009... - Page 32 9. Fix cable ties. NOTE In order for the additional hard disk unit to be addressed by the SISTORE AX application software, it must be identified as an additional data disk in the “System“ configuration menu and be formatted. Siemens Building Technologies Fire Safety &...
- Page 33 (see SISTORE AX8/AX16 500/200 User Manual). In case the device is operated in the Recycle mode, first the Stop mode needs to be configured before switched back to the recycle mode. Siemens Building Technologies Fire Safety & Security Products 03.2009...
-
Page 34: Functional Test
Search menu. Access the “Storage” menu in the OSD. Verify HDD parameters. Verify system log in regards to errors or Access System Log. reboots of the system. Siemens Building Technologies Fire Safety & Security Products 03.2009... -
Page 35: Appendix
When the DVR is in the Pre-Event recording mode, the yellow the DVR is not recording display when there is no event, and the DVR is not recording. The red display when any event occurs and the DVR starts recording. Siemens Building Technologies Fire Safety & Security Products 03.2009... -
Page 36: Sistore Ax Ras
Appendix 8.1.3 SISTORE AX RAS NOTE RAS version 3.6 is required for SISTORE AX with SATA HDDs. Problem Possible solution No selection between Watch Performance of PC not sufficient and Search displayed No display of live images Performance of PC not sufficient Siemens Building Technologies Fire Safety &... -
Page 37: Packaging For Returning The Hdd
Use a rubber block with special cut-out sections for returning multiple hard drives. All four sides of each hard drive should be protected by foam rubber. Use of padded shipping envelopes, bubble wrap or Styrofoam peanuts is not IMPORTANT considered acceptable packaging. Siemens Building Technologies Fire Safety & Security Products 03.2009... -
Page 38: Disposal
It is a precondition for reuse and recycling of used electrical and electronic equipment. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. Siemens Building Technologies Fire Safety & Security Products 03.2009... - Page 40 Issued by Siemens Building Technologies © 2009 Copyright by Fire & Security Products GmbH & Co. oHG Siemens Building Technologies D-76181 Karlsruhe Data and design subject to change without notice. Supply subject to availability. www.buildingtechnologies.siemens.com Document no. A6V10238452 Edition 09.03.2009...