EverFocus EZN850 Installation Manual
Hide thumbs
Also See for EZN850:
- Specifications (6 pages) ,
- User manual (58 pages) ,
- Specifications (11 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for EverFocus EZN850
Summary of Contents for EverFocus EZN850
-
Page 1: Installation Guide
EZN850 Installation Guide Copyright © EverFocus Electronics Corp, Release: Jan. 2009... -
Page 2: Minimum Computer Requirements
EZN850 This installation guide provides instructions for installing the EZN850 IP Camera. For all other aspects of using this product, please refer to EZN850 User’s Manual, which is available on the CD included in this package. Installation steps 1. Confirm that your PC meet minimum computer requirement listed below. - Page 3 EZN850 For example: (This web site may change without notices.) http://www.microsoft.com/downloads Dimensions Dimension of holes to holes 88.5mm/3.54” 112.7mm/4.5” 49mm/1.96” 80mm/3.2” Dimension of Bracket 220.5mm/8.68” 84mm/3.31” 106.5mm/4.19 112.7mm/4.44 199mm/7.83”...
- Page 4 EZN850 Dimension of whole camera with bracket 295mm/11.8” 107.5mm/4.3” 243.5mm/9.74” 377.3mm/15.09”...
-
Page 5: Table Of Contents
EZN850 Table Of Contents 1. Camera Component Description ................6 2. Back Panel Layout ....................7 2.1 Terminal Connector ...................8 3. Installation ........................9 3.1 Wiring and Mounting ..................10 3.2 Adjusting Camera Position ................16 3.3 Adjusting Vari-focal Lens................17 4. Lens Adjustment......................18 4.1 Lens Setting ......................18 5. -
Page 6: Camera Component Description
EZN850 1. Camera Component Description Sun shield Fixing screw for sunshield Bracket SD card slot Ethernet Video output Terminal connector Power connector Control key selection switch Control key... -
Page 7: Back Panel Layout
Connect the appropriate power to each model. N/L is used to connect to power in. PE is a ground pin. Two models of 24VAC and 100-240VAC are available as power source of EZN850 camera. N/L and PE apply to 100-240VAC model only. -
Page 8: Terminal Connector
EZN850 2.1 Terminal Connector DC OUT -Alarm: Connect to Alarm In/Out device -12VDC: Provide power source for IR illuminator (Max. load is = 1A; IR illuminator is optional) -GND: Ground pin for illuminator -RS485 (+-): A half-duplex RS-485 interface for keyboard controlling... -
Page 9: Installation
EZN850 3. Installation This section will describe, in general terms, how to install the EZN850 camera. Here are the following processes: -Wire and mount the camera. See “3.1 Wire and Mounting”. -Adjust the camera position. See “3.2 Adjusting camera position”. -
Page 10: Wiring And Mounting
EZN850 3.1 Wiring and Mounting 1. Wire internet cable, power cable and Alarm/RS485 cable through the bracket. Note!! Please use Internet cable without RJ45 connector otherwise you cannot go through cable gland. LAN cable Power cable Alarm/RS485 cable 2. Fix the bracket to wall by using 4 screws. - Page 11 EZN850 3. Open camera’s back cover: Loose the 2 screws from the back panel cover, then open the back cover. Screws for back panel 4. Take off the cap of cable gland which is under the camera. Power cable (Φ10.3mm)
- Page 12 EZN850 Note!! The holes of cable gland were plugged by stoppers, please remove the stoppers when you need to use it for connection. 5. Take internet cable, power cable and Alarm/RS485 cable to pass through cable gland, place them into camera housing.
- Page 13 EZN850 LAN cable Power cable Alarm/RS485 cable Note!! 1. Power cable’s diameter must be less than 10 mm 2. Alarm/RS485 cable must be less than 5 mm 6. Close the waterproof cap and fix cable gland to the base of camera firmly.
- Page 14 EZN850 Fix the camera body to bracket by using the 4 shorter screws. 8. Connect internet cable to RJ45 connector. Before connection, please check if you are using T568A or T568B as pin assignment in the network. T568A and T568B Wiring...
- Page 15 EZN850 *Warning* • To prevent electrical shock, turn off the electrical power before making electrical connections. • Do not connect high voltage power to the camera. It may damage the camera. • Do not short circuit the power leads and expose the wire when connecting the power supply to the camera.
-
Page 16: Adjusting Camera Position
EZN850 Screws for back panel 3.2 Adjusting Camera Position Adjust camera’s angle vertically or horizontally by using hex key included in package. Loose this screw to make angle adjustment vertically Loose this screw to make angle adjustment horizontally... -
Page 17: Adjusting Vari-Focal Lens
EZN850 3.3 Adjusting Vari-focal Lens EZN850 offers a 6~50mm lens that can be motorized controlled. Open camera’s base, a control key is attached at inner side of the base. Detach the control key and use this key for OSD or Lens setting. -
Page 18: Lens Adjustment
EZN850 4. Lens Adjustment 4.1 Lens Setting Please turn the control key selection switch at the back panel to “Lens” ( ). Use the control key to do lens setting. Mini joystick The Cursors & mini stick Turn joystick up ( ) or down ( ) to adjust zoom in / zoom out,... -
Page 19: Osd Configuration
EZN850 5. OSD Configuration Please turn the control key selection switch at the back panel to “OSD” ( Detach the control key and use this key to do OSD setting. Mini joystick The Cursors & mini stick Bring up the General OSD Menu Simply press the mini-joystick to bring up the general OSD menu. - Page 20 EZN850 SETUP LENS DC <┘ > LENS SHUTTER LEVEL |+++++++++| 25 WHITE BAL. BACKLIGHT MIDDLE AUTO <┘ SENS-UP SPECIAL <┘ Sub-Menu EXIT Main Menu Note!! For those selected items with “ ” sign in the end, they have the sub-menu for further settings.
-
Page 21: Network Connection
EZN850 6. Network Connection This section tells you how to do different types of network connections to IP cameras. a. Router or LAN connection This is the most common connection that allows multiples PC to see IP cameras/ video servers in pre-existing LAN through a router. - Page 22 EZN850 c. One to one connection from PC to IP camera You can connect directly without switch. However, only the PC connecting to camera can view the IP camera.
-
Page 23: Assign Ip Address By Utility
Please install IP utility software from CD before you go through the following process. Please note the following procedures are an example according to EZN850 default values. These values may vary with your network system. Please consult your ISP or network administrators for more detail of network setting reference. - Page 24 Mac Address, Machine Name, Machine Type, IP Type, Subnet Mask, Gateway Address, DNS1 Address, and DNS2 Address. c. The IP address of EZN850 will be automatically detected and assigned. Select the IP camera you want to see or configure. d. Click "Connect to selected IP". You will go into IP camera web browser. Then finished! Note!! Default Administrator User ID is "user1"...
-
Page 25: Manually Assign An Ip Address And Change Network Setting
EZN850 7.2 Manually assign an IP address and change network setting a. Instead of clicking "Connect to selected IP" after select IP camera, click "Login". You will be asked to enter Administrator's "User ID" and "Password". In order to make configuration as highest security level, only administrator level is allowed to do network setting. - Page 26 After the change is done, press “Set Configuration” to confirm setting. c. Click “Connect to selected IP” and the browser will automatically connect to the EZN850 network page. Note!! Please use Internet Explorer as default Browser.
- Page 27 EZN850 d. When you see the following menu, it means you log in successfully. Please refer to User’s manual for detailed camera setting. e. Exit: Close IP Utility window to finish your setting.
- Page 28 Chiba city 261-7118, Japan www.everfocus.com TEL: +81-43-212-8188 FAX: +81-43-297-0081 www.everfocus.co.jp Your EverFocus product is designed and Ihr EverFocus Produkt wurde entwickelt und manufactured with high quality materials and hergestellt mit qualitativ hochwertigen Materialien components which can be recycled and reused.