Safety Warnings Specific For Sanding Operations - Dremel Micro Original Instructions Manual

the wheel in the cut and the possibility of
kickback or wheel breakage.
d. Do not position your hand in line with and
behind the rotating wheel. When the wheel,
at the point of operation, is moving away from
your hand, the possible kickback may propel
the spinning wheel and the power tool directly
at you.
e. When wheel is pinched, snagged or when
interrupting a cut for any reason, switch
off the power tool and hold the power
tool motionless until the wheel comes to
a complete stop. Never attempt to remove
the cut-off wheel from the cut while the
wheel is in motion otherwise kickback may
occur. Investigate and take corrective action
to eliminate the cause of wheel pinching or
snagging.
f. Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed
and carefully re-enter the cut. The wheel
may bind, walk up or kickback if the power
tool is restarted in the workpiece.
g. Support panels or any oversized
workpiece to minimize the risk of wheel
pinching and kickback. Large workpieces
tend to snag under their own weight. Supports
must be placed under the workpiece near the
line of cut and near the edge of the workpiece
on both sides of the wheel.
h. Use extra caution when making a "pocket
cut" into existing walls or other blind
areas. The protruding wheel may cut gas or
water pipes, electrical wiring or objects that
can cause kickback.
SAFETY WARNINGS SPECIFIC FOR
a. Do not use excessively oversized
sanding disc paper. Follow manufacturers
recommendations, when selecting sanding
paper. Larger sanding paper extending
beyond the sanding pad presents a laceration
hazard and may cause snagging, tearing of
the disc or kickback.
SAFETY WARNINGS SPECIFIC FOR
a. Do not allow any loose portion of the
polishing bonnet or its attachment strings
to spin freely. Tuck away or trim any loose
attachment strings. Loose and spinning
attachment strings can entangle your fingers
or snag on the workpiece.
SAFETY WARNINGS SPECIFIC FOR
a. Be aware that wire bristles are thrown by
the brush even during ordinary operation.
Do not overstress the wires by applying
excessive load to the brush. The wire
bristles can easily penetrate light clothing and/
or skin.
b. Allow brushes to run at operating speed
for at least one minute before using them.
During this time no one is to stand in front
or in line with the brush. Loose bristles or
wires will be discharged during the run-in
time.
SANDING OPERATIONS
POLISHING OPERATIONS
WIRE BRUSHING OPERATIONS
c. Direct the discharge of the spinning wire
brush away from you. Small particles and
tiny wire fragments may be discharged at high
velocity during the use of these brushes and
may become imbedded in your skin.
d. If the use of a guard is recommended
for wire brushing, do not allow any
interference of the wire wheel or brush
with the guard. Wire wheel or brush may
expand in diameter due to work load and
centrifugal forces.
e. Do not exceed 15000 min
wire brushes.
DO NOT WORK WITH
WARNING
!
MATERIALS CONTAINING
ASBESTOS (ASBESTOS IS CONSIDERED
CARCINOGENIC).
TAKE PROTECTIVE MEASURES
WARNING
!
WHEN WORKING. DUST CAN
DEVELOP THAT IS HARMFUL TO ONE'S HEALTH,
COMBUSTIBLE OR EXPLOSIVE (SOME DUSTS ARE
CONSIDERED CARCINOGENIC); WEAR A DUST MASK
AND WORK WITH DUST/ CHIP EXTRACTION WHEN
CONNECTABLE.
ENVIRONMENT
DISPOSAL
The machine, accessories and packaging should
be sorted for environmental-friendly recycling.
ONLY FOR EUROPEAN COUNTRIES
Do not dispose of power tools into
household waste!
According the European Guideline
2012/19/EC for Waste Electrical and
Electronic Equipment and its
implementation into national right, power
tools that are no longer usable must be
collected separately and disposed of in
an environmentally correct manner.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Voltage Rating 7,2 V
Amperage Rating 1 Ah
No Load Speed n 5000 – 28000 min
o
Rated Speed n 28000/min
Collet Capacity 0,8 mm, 1,6 mm, 2,4 mm,
3,2 mm
SPECIFICATIONS CHARGER
Input 230-240 V, 50 - 60 Hz, 26 W
Output 3,6-10,8 V, 1,5 A
EXTENSION CORDS
Use completely unrolled and safe extension cords
with a capacity of 5 Amps.
13
when using
–1
–1