Used Symbols; Safety Warnings; Specifications - Dremel VERSATIP 2000 Original Instructions Manual

USED SYMBOLS

1
READ THESE INSTRUCTIONS

SAFETY WARNINGS

READ ALL SAFETY WARNINGS
WARNING
!
AND ALL INSTRUCTIONS
Failure to follow the warnings and instructions may
result in fire and/or serious injury. Save all warnings
and instructions for future reference. Before using
the tool, make sure you read and understand this
manual completely.
WORK AREA SAFETY
a. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b. Do not keep combustible materials near the
tool.
c. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
d. Only use the tool outdoors or in well-ventilated
rooms.
PERSONAL SAFETY
a. Stay alert, watch what you are doing and use
common sense when operating the tool. Do
not use the tool while you are tired or under
the influence of drugs, alcohol or medication.
A moment of inattention while operating tools may
result in serious personal injury.
b. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
c. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the tool in unexpected situations.
d. Dress properly. There is a danger of burning
yourself with the flame or with liquid soldering tin.
Wear protective clothing to protect yourself against
burns. Keep your hair, clothing and gloves away
from the flame. Loose clothes or long hair can
catch fire.
e. Secure the workpiece. Use a clamping device to
hold the workpiece. This allows you to use both
hands to operate the tool.
f. Do not use the appliance when it is leaking
(gas smell), shows any sign of damage or is
malfunctioning.
g. If the appliance is leaking (gas smell)
immediately take it outside and check the leak-
tightness without a flame. Always use soapsuds.
h. (Re)filling the gas tank must be done in
a well-ventilated place far away from any
possible sources of ignition, open flames,
pilot lights, electrical cookware and away from
other persons. Be sure to observe the safety
instructions and warning notices on the refill
container.
GB
i. Do not make any modifications to the tool.
TOOL USE AND CARE
a. Store the tool in an appropriate place with an
ambient temperature between 10°C and 50°C.
Allow your tool to fully cool down before
storing. Unused tools should be stored away
from children in a dry location. Switch off all
unused tools.
b. Always allow the tool to fully cool down before
removing/replacing tips and/or installing/
replacing the nozzle.
c. Extremely flammable gas under pressure.
d. Do not use near sparks or an open flame.
e. Do not puncture or incinerate the gas tank or
store at a temperature above 50°C.
f. Keep out of reach of children.
g. Do not try to disassemble this unit.
SERVICE
a. Have the tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the tool is
maintained.

SPECIFICATIONS

Model number . . . . . . . . . 2000
Power source . . . . . . . . . . Refined butane gas
Gas tank capacity . . . . . . ± 17 ml / ± 9 grams
Run time . . . . . . . . . . . . . . ± 45 minutes
Heat-up time . . . . . . . . . . Instantly (open flame)
Nominal heat input . . . . . . 12 g/h
Cool-down time . . . . . . . . 17 min (< 25°C) (tips)
Temperature . . . . . . . . . . . 1200°C (open flame)
Weight . . . . . . . . . . . . . . . 135 grams (empty tool)
GENERAL
A . Catalyst
B . Flame guard
C . Flame guard nut
D . Ceramic insulator
E . Ignition switch
F . Child safety lock
G . Lock button
H . Flame control lever
I . Gas tank
J . Filling valve
K . Shaping knife
L . Wide flame head
M . Deflector
N . Soldering tip
O . Cutting knife
P . Hot air tip
Q . Wrenches (7 & 8 mm)
3
(highest setting)
± 90 minutes
(lowest setting)
± 25 seconds (tips)
15 min (< 25°C)
(flame guard)
680°C (hot air)
550°C (tips)
2