Using The Timer - Denon dra-f101 Operation Instruction Manual

ENGLISH
9

USING THE TIMER

(1) Setting the Current Time (24-hour display)
Example: Setting the current time to 19:30
2 3,5,7 4,6
TUNING
MEMORY SOURCE
FUNCTION
TONE TIMER RDS / SET DOWN UP BAND DIRECT
SYSTEM
ON / STANDBY
PHONES
1
ON / STANDBY
1
Turn on the power.
Press the TIMER button for at least
3 seconds.
• "TIME" flashes on the display.
If the time is already set,
2
"EVERYDAY" is displayed.
Press one of the TUNING buttons
to display "TIME", then perform
step 3.
Press the MEMORY/SET button.
• The hours position flashes.
3
(2) Before Setting the Timer
Be sure to set the current time. If the current time is not set, the timer standby indicator ("
2
timer will not function.
Be sure to preset the station before setting the timer. (Refer to "Presetting AM and FM stations" on page 14.)
2
The DRA-F101 is equipped with two types of timers: the everyday time which turns the power on and off at the
2
same times every day, and the once timer that turns the power on and off only once.
Do not change the timer standby mode after the timer is activated (after the timer on time is reached). The timer may
2
not operate properly.
It is not possible to set the timer start and end times to the same time.
2
If the display or operation is not normal, unplug the power cord, then plug it back in while pressing the memory/set
2
button (MEMORY/SET). This restores the tuner to the initial default values. After doing this, reset the presettings,
current time and timer settings.
When setting the timer to operate the CD player, MD recorder or cassette deck, do so with a disc or cassette loaded
2
and the disc holder or cassette holder closed. The timer will not operate properly if no disc or cassette is loaded or if
the disc holder or cassette holder is open.
16
Use the TUNING buttons
to input the hours (19).
• "19" flashes in the hours
position.
4
VOLUME
Press the MEMORY/SET button.
• "19" stops flashing, remaining
lit, and the minutes position
AM-FM STEREO RECEIVER DRA-F101
starts flashing.
5
SYSTEM
Use the TUNING buttons to
input the minutes (30).
• "30" flashes in the
minutes position.
6
TIMER
Press the MEMORY/SET button
at the sound of the chime of a
time service, etc.
• "30" stops flashing, remaining
lit, and the current time is
7
MEMORY
displayed.
/ SET
The number changes continuously when one of the
tuning buttons (TUNING UP or DOWN) is pressed.
If the time is already set when step 2, 3 is performed,
both the hours and minutes positions flash.
(3) Setting the Timer
TUNING
DOWN UP
The timer function lets you switch the power between
2
the on and standby modes automatically at the desired
times.
When connected in a system with the D-F101 series,
2
the timer can be used to play a CD, cassette or MD or
to record from the tuner onto the MD recorder or
cassette deck ("air check").
Example: Using the everyday timer to listen to the
station stored at preset number 3 (FM 98.00 MHz)
MEMORY
from 12:35 to 12:56
/ SET
2
FUNCTION
TONE TIMER
SYSTEM
ON / STANDBY
PHONES
TUNING
DOWN UP
1,18 4, 6, 8,10,12,14,16
1
Turn on the power.
MEMORY
/ SET
Press the TIMER button for at least
3 seconds.
• "EVERYDAY" is displayed.
2
If the time is not set, "TIME" is displayed.
Perform steps 3 to 7 on page 16, then start
the timer setting over.
Press one of the TUNING
3
buttons to display
"EVERYDAY" or "ONCE".
") will not light and the
Press the MEMORY/SET button.
• This sets the unit to the timer
setting mode's
setting mode.
4
Example: When the everyday timer is
selected
Use the TUNING buttons
to switch the function to
"TUNER".
5
The function switches as follows each time
the button is pressed:
3, 5, 7, 9,11,13,15,17
VOLUME
TUNING
MEMORY SOURCE
RDS / SET DOWN UP BAND DIRECT
AM-FM STEREO RECEIVER DRA-F101
Press the MEMORY/SET button.
6
• "TUNER" is stored in the
memory as the timer function.
SYSTEM
ON / STANDBY
Use the TUNING buttons
to set preset number 3.
7
TIMER
Press
button.
• The preset station is stored in
the memory and the timer on
TUNING
DOWN UP
time setting mode is set.
"E"
8
alternately in the display in the
steps 8 to 11.
MEMORY
/ SET
function
<Setting the timer on
time>
Use the tuning buttons to set
the hours position to "12".
9
TUNING
DOWN UP
: When the TUNING UP button is pressed.
: When the TUNING DOWN button is
pressed.
MEMORY
/ SET
TUNING
DOWN UP
the MEMORY/SET
MEMORY
/ SET
and "oN" appear
TUNING
DOWN UP