Testing Gas Supply Pressure; Check Manifold Pressure; Gas Pipe Capacity - Lennox G43UF SERIES Unit Information

Nominal Nominal Internal Internal
Iron Pipe Size Diameter
−Inches(mm) −Inches(mm)
1/4 .364
(6.35) (9.246)
3/8 .493
(9.53) (12.522)
1/2 .622
(12.7) (17.799)
3/4 .824
(19.05) (20.930)
1 1.049
(25.4) (26.645)
1−1/4 1.380
(31.75) (35.052)
1−1/2 1.610
(38.1) (40.894)
2 2.067
(50.8) (52.502)
2−1/2 2.469
(63.5) (67.713)
3 3.068
(76.2) (77.927)
4 4.026
(101.6) (102.260)
NOTE−Capacity given in cubic feet of gas per hour (kilo liters of gas per hour) and based on 0.60 specific gravity gas.
IMPORTANT
The furnace must be isolated from the gas supply
piping system by closing its individual manual
shut−off valve during any pressure testing of the
gas supply piping system at test pressures equal
to or less than 1/2 psig (3.45 kPa).
The furnace and its individual shut−off valve must
be disconnected from the gas supply piping sys-
tem during any pressure testing of the system at
test pressures greater than 1/2 psig (3.45 kPa). See
figure 39.
When checking piping connections for gas leaks, use pre-
ferred means. Kitchen detergents can cause harmful corro-
sion on various metals used in gas piping. Use of a specialty
Gas Leak Detector is strongly recommended. It is available
through Lennox under part number 31B2001. See Corp.
8411−L10, for further details.
WARNING
Do not use matches, candles, flame or any other
source of ignition to check for gas leaks.
D−Testing Gas Supply Pressure
When testing supply gas pressure, use the 1/8" N.P.T.
plugged tap or pressure post located on the gas valve to
facilitate test gauge connection. See figure 14. Check gas
TABLE 15
GAS PIPE CAPACITY − FT
10 20 30
(3.048) (6.096) (9.144)
43 29 24
(1.13) (.82) (.68)
95 65 52
(2.69) (1.84) (1.47)
175 120 97
(4.96) (3.40) (2.75)
360 250 200
(10.19) (7.08) (5.66)
680 465 375
(19.25) (13.17) (10.62)
1400 950 770
(39.64) (26.90) (21.80)
2100 460 1180
(59.46) (41.34) (33.41)
3950 2750 2200
(111.85) (77.87) (62.30)
6300 4350 3520
(178.39) (123.17) (99.67)
11000 7700 6250
(311.48) (218.03) (176.98)
23000 15800 12800
(651.27) (447.39) (362.44)
Page 34
/HR (kL/HR)
3
Length of Pipe−Feet(m)
40 50 60
(12.192) (15.240) (18.288)
20 18 16
(.57) (.51) (.45)
45 40 36
(1.27) (1.13) (1.02)
82 73 66
(2.32) (2.07) (1.87)
170 151 138
(4.81) (4.28) (3.91)
320 285 260
(9.06) (8.07) (7.36)
660 580 530
(18.69) (16.42) (15.01)
990 900 810
(28.03) (25.48) (22.94)
1900 1680 1520
(53.80) (47.57) (43.04)
3000 2650 2400
(84.95) (75.04) (67.96)
5300 4750 4300
(150.07) (134.50) (121.76)
10900 9700 8800
(308.64) (274.67) (249.18)
line pressure with unit firing at maximum rate. Low pres-
sure may result in erratic operation or underfire. High pres-
sure can result in permanent damage to gas valve or over-
fire. For natural gas units, operating pressure at unit gas
connection must be between 4.5" W.C. and 13.0" W.C. For
L.P. gas units, operating pressure at unit gas connection
must be between 10.5" and 13.0" W.C.
On multiple unit installations, each unit should be checked
separately, with and without units operating. Supply pres-
sure must fall within range listed in previous paragraph.
E−Check Manifold Pressure
Manifold pressure is the manifold pressure measured
when the gas valve regulator is operating at factory preset
level sensing atmospheric pressure.
IMPORTANT
The White Rodgers 36G gas valve (figure 14) is
equipped with pressure posts for measuring supply
and manifold pressures. The posts provide built−in
hose connections and have an integral 3/32" Allen−
head screw. Rotate the screw counterclockwise one
full turn to permit pressure measurement. Reseat the
screw (rotate one full turn clockwise) after measure-
ments have been taken to prevent gas leakage.
After line pressure has been checked and adjusted, check
manifold pressure. Move pressure gauge to outlet pres-
sure tap located on unit gas valve (GV1).
70 80 90
(21.336) (24.384) (27.432)
15 14 13
(.42) (.40) (.37)
33 31 29
(.73) (.88) (.82)
61 57 53
(1.73) (1.61) (1.50)
125 118 110
(3.54) (3.34) (3.11)
240 220 205
(6.80) (6.23) (5.80)
490 460 430
(13.87) (13.03) (12.18)
750 690 650
(21.24) (19.54) (18.41)
1400 1300 1220
(39.64) (36.81) (34.55)
2250 2050 1950
(63.71) (58.05) (55.22)
3900 3700 3450
(110.43) (104.77) (97.69)
8100 7500 7200
(229.36) (212.37) (203.88)
100
(30.480)
12
(.34)
27
(.76)
50
(1.42)
103
(2.92)
195
(5.52)
400
(11.33)
620
(17.56)
1150
(32.56)
1850
(52.38)
3250
(92.03)
6700
(189.72)