Table of Contents
Advertisement
5 Start playing the tape (press
signals from tape will be monitored.
6 At the point where the punch is to occur, press
.
RECORD
The
key flashes, and the
RECORD
indicator(s) of any armed track(s) light
TION
steadily.
At any time when the rehearsal key is lit or
flashing, this means that recording will not
actually be carried out, even if the
key and/or the
REC FUNCTION
lit.
7 At the point where you want to punch out,
press
.
PLAY
The
REC FUNCTION
track(s) starts flashing again. The
key goes out.
8 After the post-roll period, the tape returns to
the pre-roll point (the punch-in point minus
the pre-roll offset).
The
indicator now lights steadily, show-
RHSL
ing that the DA-98HR is in rehearsal mode.
NOTE
If you want to alter the pre-roll and post-roll times, see
6.6.5, "Editing the preroll and postroll times". The punch-in
and punch-out points will remain the same while you
change the pre- and post-roll times.
6.6.4
Setting and editing punch points
using the menus
1 Press the
(rehearsal) key
RHSL
until the indicator lights steadily).
2 Press the
AUTO MON
light).
3 Go to menu group 1 and select the
Point
option using the cursor keys and
:
ENTER
P u n c h - i n
P o i n t
S a m p l e
S u b
0 0 : 0 9 : 2 1 : 1 2 . 0 0 0 0
In the screen above, the sub-frame units are
samples. Select the sub-frame units, which can
either be 1/100 of a frame, or samples, by mov-
ing the cursor to the right field (here it is
but for 1/100 frame units it is
6 – Basic Operations–Punch-in and punch-out
), and the
PLAY
REC FUNC-
RECORD
indicators are
indicator(s) of any armed
RECORD
L
twice (or
i
key
(the indicator will
In
f r a m e
2 9 D F
s m
sm
,
sf
) on the bot-
tom line of the display, and using the § and ¶
keys to change between them.
4 Use the Á and Ó keys to select the "field"
(hours, minutes, seconds or sub-frame units)
that you want to edit, and use the § and ¶
keys to change the values. The function keys
can also be used as number keys (4.4, "Using
the function keys as number keys").
5 Press
to return to menu group 1.
ESCAPE
6 Select
Out Point
for the punch-out point.
NOTE
You can also use this process to edit punch points which
have been set "on the fly").
7 Locate the tape to the punch-in point (minus
the pre-roll time) by pressing
6.6.5
Editing the preroll and postroll
times
As shipped from the factory, the DA-98HR will posi-
tion the tape 5 seconds before the punch-in point,
whether this has been set by you, or set automatically
(as described above).
The post-roll is factory set to 3 seconds. You can alter
both these times using the following method:
1 Enter menu group 1, move the cursor to the
Pre/Post
menu option, and press
:
ENTER
P r e - r o l l
P o s t - r o l l
P r e
0 0 m 0 5 s
2 Use the Ó and Á keys to position the cursor
by the "field" (minutes or seconds) that you
want to change and use the § and ¶ keys to
alter the value.
You can also use the function keys to enter the
value directly, as described in 4.4, "Using the
function keys as number keys".
Since there is little point in setting pre- and postroll
times to frame accuracy, you can only set these val-
ues to second accuracy.
The minimum value you can set for preroll is 5
seconds and the maximum value is 59 minutes
59 seconds.
and repeat the process
O
.
LOC 1
P o s t
0 0 m 1 0 s
37
TASCAM DA-98HR
Advertisement
Table of Contents
