Table of Contents
Advertisement
9 – Operations related to timecode–Recording timecode
cases, we suggest that you use the internal generator or
the tape as sources for recording timecode.
If you are recording timecode only, we suggest that you do
not use external sources for recording timecode.
Tape
Set
as the source as described immediately
above, and use
ABS
or
ABS-Ofs
setting" and 9.2.3, "ABS-Ofs setting") as tape time-
code sources. This will ensure an accurate relation-
ship between the timecode and the ABS timing
reference (the fact that the generator must be started
manually means that there will not be a tight relation
between timecode and the ABS timing).
This will also allow you to synchronize multiple
DTRS units accurately to external timecode, even if
the slave units are not timecode-based.
If
TcTrack
is set as the Tape TC mode (9.2.1,
Tape
"TcTrack setting"), and
timecode source, the display shows
(Assemble)
. See 9.3.4, "Assembling time-
code" for details of how to use this function.
9.3.2
Recording timecode using the
generator
1 Insert a formatted tape into the DA-98HR.
It is also possible to format and stripe a new
tape simultaneously, by setting up the format-
ting procedure as described in 6.2, "Format-
ting a tape" and then following the instructions
below.
2 Select timecode as the timing reference (9.1.3,
"Selecting TC or ABS timing").
3 From menu group 8, select a frame rate (9.4,
"Selecting the frame rate").
4 From menu group 8, move the cursor to
TcRec Src
(source for timecode
recording) and press
T C
R e c o r d
S o u r c e
G e n e r a t o r
5 Use the § and ¶ keys to select the source of
Generator TC
the timecode as
(9.2.2, "ABS
is selected as the
Tape
:
ENTER
T C
.
6 Go to menu group 8, move the cursor to
Start
(generator start time) and press
ENTER
:
G e n e r a t e
S t a r t
0 0 : 0 0 : 0 0 : 0 0
7 Use the Ó and Á keys to select the field
(hours, minutes, seconds or frames) to be
edited, and the § and ¶ keys to change the
value.
You can also use the function keys as number
keys to input the value directly, as described in
4.4, "Using the function keys as number keys".
8 Go to menu group 8, move the cursor to
Mode
(generator mode) and press
G e n e r a t e
M o d e
0 0 : 5 5 : 0 0 : 0 0
R u n / S t o p
S t o p
9 Press the
key
TC REC
to flash.
10 With the cursor under the
the display, press the § or ¶ key to start the
timecode generator. The tape counter shows
the generated timecode, as does the display.
11 Press and hold the
RECORD
key and the tape starts recording time-
PLAY
code. The
indicator lights steadily.
TC REC
12 Press the § or ¶ key with the cursor under
the
Run/Stop
on the display to stop the
timecode generator.
You can also start recording and then start the time-
code generator. In this case, an warning message
appears on the display screen as you start recording,
to tell you that there is no timecode source.
If the
Mode
field is set to
than
Reset
, stopping the generator and then re-
starting it picks up the timecode values from where it
left off.
Conversely, setting this field to
from the start time set above every time the generator
is stopped and re-started.
It is also possible to "drop into" timecode recording
by starting the transport in record mode and then
Gen
T i m e
3 0 N D
Gen
:
ENTER
3 0 N D
M o d e
R e s e t
k
. The indicator starts
Run/Stop
on
and
press the
Continue
rather
Reset
restarts
59
TASCAM DA-98HR
Advertisement
Table of Contents
