Table of Contents

Advertisement

Para obtener un ejemplar en Español de este
Manual del propietario, visite www.heatnglo.com.
Models:
SL-550BE-B
SL-550BE-IPI-B
• Important operating
a n d m a i n t e n a n c e
instructions included.
WARNING: If the information in these
instructions is not followed exactly, a fi re
or explosion may result causing property
damage, personal injury, or death.
• DO NOT store or use gasoline or other fl am-
mable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Immediately call your gas supplier from a
neighbor's phone. Follow the gas suppli-
er's instructions.
- If you cannot reach your gas supplier, call
the fi re department.
• Installation and service must be performed
by a qualifi ed installer, service agency, or the
gas supplier.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer's instructions
and the manufactured home construction and safety standard,
Title 24 CFR, Part 3280 or Standard for Installation in Mobile
Homes, CAN/CSA Z240MH, in Canada.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
NOTICE
DO NOT DISCARD THIS MANUAL
• Read, understand and follow
these instructions for safe
installation and operation.
Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09
Pour demander un exemplaire en français de ce Manuel
du propriétaire, visitez www.heatnglo.com.
Owner's Manual
Installation and Operation
• Leave this manual with
party responsible for use
and operation.
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fi replace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other fl ammable
materials.
• Keep clothing, furniture, draperies and other fl ammable
materials away.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fi xed glass panel. DO
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fi tter.
See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.
Installation and service of this appliance should be
performed by qualifi ed personnel. Hearth & Home
Technologies suggests NFI certifi ed or factory trained
professionals, or technicians supervised by an NFI
certifi ed professional.
1

Advertisement

Table of Contents
loading

Summary of Contents for Heat & Glo SL-550BE-B

  • Page 1 Technologies suggests NFI certifi ed or factory trained This appliance is only for use with the type(s) of gas indicated professionals, or technicians supervised by an NFI on the rating plate. certifi ed professional. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 2: Congratulations

    00,000 00,000 00,000 00,000 MIN. MIN. INPUT INPUT BTUH: BTUH: 00,000 00,000 00,000 00,000 Serial Serial ORIFICE ORIFICE SIZE: SIZE: #XXXXX #XXXXX #XXXXX #XXXXX XXXXXXXX XXXXXXXX (Serie): (Serie): Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 3: Table Of Contents

    G. Wall Switch Installation for Fan (Optional) ... . 55 6 Termination Locations A. Vent Termination Minimum Clearances ....22 Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 4 D. Contact Information ......83 = Contains updated information. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 5: Limited Lifetime Warranty

    B. Limited Lifetime Warranty Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 6 B. Limited Lifetime Warranty (continued) Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 7: Listing And Code Approvals

    • A 110-120 VAC circuit for this product must be protected with ground-fault circuit-interrupter protection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 8: Requirements For The Commonwealth Of Massachusetts

    VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OB- of the installation. STRUCTIONS”. See Gas Connection section for additional Common- wealth of Massachusetts requirements. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 9: User Guide

    • Install a switch lock or a wall/remote control with child protection lockout feature. DECORATIVE DOORS (NOT SHOWN) SECTION 2.D. FIXED GLASS ASSEMBLY (NOT SHOWN) SECTION 14G. MANTEL FAN KIT SECTION 2.C HEARTH Figure 2.1 General Operating Parts Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 10: Fan Kit (Optional)

    • A standing pilot ignition will have a red or black ignitor button (refer to Figure 2.3). • An Intellifi re ignition system will not have a button. Figure 2.2 Clear Space Figure 2.3 Ignitor Button Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 11: Lighting Instructions (Ipi)

    For additional information on operating your Hearth & Home Technologies fi replace, please refer to www.fi replaces.com. Final inspection by Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 12: Lighting Instructions (Standing Pilot)

    Hearth & Home Technologies fi replace, please refer to www.fi replaces.com. 4. Push in gas control knob slightly and turn clock- wise to OFF”. DO NOT force. 5. Close control access panel. Final inspection by 464-903H Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 13: After Fireplace Is Lit

    In an Intellifi re ignition system it is normal to see the pilot fl ame, but it should turn off when continually? ON/OFF is turned off. In a standing pilot system the pilot will always stay on. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 14: Maintenance And Service

    • Carefully set fi xed glass assembly in place on fi replace. Hold glass in place with one hand and secure glass latches with the other hand. • Reinstall door or decorative front. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 15: Maintenance Tasks-Qualifi Ed Service Technician

    • Inspect for paint condition, warped surfaces, corrosion sensing rod. Replace pilot as necessary. (IPI only) or perforation. Sand and repaint as necessary. • Replace fi replace if fi rebox has been perforated. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 16 Figure 3.1 IPI Pilot Flame Patterns Figure 3.2 Standing Pilot Flame Patterns Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 17: Installer Guide

    IN CEILING JOISTS FRAMING/HEADER (SECTION 8.C) (SECTION 5.B) OPTIONAL WALL SWITCH MANTEL AND MANTEL LEG (SECTION 5.E, 13.A) SURROUND HEARTH EXTENSION GAS LINE (SECTION 11) Figure 4.1 Typical System Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 18: Design And Installation Considerations

    Reciprocating saw Manometer Flat blade screwdriver Non-corrosive leak check solution 1/2 - 3/4 in. length, #6 or #8 Self-drilling screws One 1/4 in. female connection (for optional fan). Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 19: Framing And Clearances

    E Min. F Min. 59-1/2 62-1/4 16-1/4 48-1/2 68-3/4 15-1/16 7-1/2 7-1/8 SL-550BE-B See Section 5.E for SL-550BE-IPI-B Alcove Installation 1067 1511 1117 1581 1232 1746 Figure 5.1 Appliance Locations Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 20: Constructing The Appliance Chase

    SL-550BE-B SL-550BE-IPI-B * Adjust framing dimensions for interior sheathing (such as sheetrock) C** Add 12 inches for rear venting with one 90º elbow. Figure 5.2 Clearances to Combustibles Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 21: Mantel And Wall Projections

    Note: Clearance from OR COMBUSTIBLE opening to perpendicular wall. MATERIAL Figure 5.6 Wall Projection (Acceptable on one side of opening) 1/2 in. NON-COMBUSTIBLE ZONE Figure 5.4 Non-Combustible Zone Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 22: Termination Locations

    Over 16/12 to 18/12 ..........7.0 Over 18/12 to 20/12 ..........7.5 Over 20/12 to 21/12 ..........8.0 * 3 foot minimum in snow regions Figure 6.1 Minimum Height From Roof To Lowest Discharge Opening Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 23 Figure 6.3 Minimum Clearances for Termination CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE INSTALLED. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 24: Vent Information And Diagrams

    76 to 152 DVP12A 3 to 12 76 to 305 DVP12MI 3 to 12 76 to 305 DVP24MI 3 to 24 76 to 610 Figure 7.2 DVP Pipe Effective Length Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 25: Use Of Flex Vent

    However, 1 in. the vent attachment point and the fi restop CLEARANCE location are considered to be supports. Figure 7.3 Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 26: Vent Diagrams

    Note: There MUST be a 25% reduction in total H when using fl ex vent except when using the simple up and out installation (see Figure 7.3). Figure 7.4 Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 27 fi rst elbow. • When using DVP-TB1 termination cap on top vented fi replaces, a three foot minimum vertical vent section is required before installing fi rst elbow. Figure 7.5 Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 28 • When using SLP-HRC-SS and SLP-HRC-ZC- SS termination caps on top vented fi replaces, a one foot minimum vertical vent section is required before installing fi rst elbow. Figure 7.6 Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 29 fl ame height. If the vent confi guration has a total vertical of 15-60 feet, an exhaust restrictor may be needed. The exhaust restrictor can be located in the appliance manual bag. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 30 Note: There MUST be a 25% reduction HORIZONTALLY in total H when using fl ex vent except when using the simple up and out installation (see Figure 7.3). Figure 7.10 Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 31 Note: There MUST be a 25% reduction in total H when using fl ex vent except when using the simple up and out installation (see Figure 7.3). Figure 7.11 Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 32 = 24 in. Max. (610 mm) components only. Figure 7.12 Rear Vent - Horizontal Termination = 9 in. (229 mm) Maximum One 45º Elbow Note: Use DVP Series components only. Figure 7.13 Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 33 6 ft. 1.8 m 13-1/2 ft. 4.1 m HORIZONTALLY MAX. = 7-1/2 ft. (2.3 m) MAX. = 13-1/2 ft. (4.1 m) MAX. = 40 ft. (12.2 m) Figure 7.15 Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 34 6-1/2 ft. 2.0 m 3 ft. 914 mm H MAX. = 6-1/2 ft. (2 m) V + H+ H MAX. = 40 ft. (12.2 m) INSTALLED HORIZONTALLY Figure 7.17 Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 35 4.4 m MAX. = 7-1/2 ft. (2.3 m) MAX. = 14-1/2 ft. (4.4 m) MAX. = 40 ft. (12.2 m) Note: Use DVP Series components only. Figure 7.18 Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 36 CAUTION! DO NOT use any fl ue restrictor when vent- ing with the DV-46DVA-GCL adapter and LINK-DV30B kit. This may result in poor fl ame appearance, sooting, pilot malfunction, or overheating. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 37: Rear Vent

    10 ft. 3.05 m 0 ft. 0 mm Minimum 10 ft. 3.05 m Maximum 40 ft. 12.2 m 2 ft. 610 mm Maximum 40 ft. 12.2 m Figure 7.21 Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 38: Vent Clearances And Framing

    * Shows center of vent framing hole for top or rear venting. The center of the hole is one (1) in. (25.4 mm) above the center of the horizontal vent pipe. Figure 8.2 Wall Penetration Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 39: Install The Ceiling Firestop

    INSTALL ATTIC INSULATION SHIELDS BEFORE OR AFTER INSTALLATION OF VENT SYSTEM 3 FASTENERS PER SIDE CEILING FIRESTOP CEILING FIRESTOP INSTALLED BELOW CEILING INSTALLED ABOVE CEILING Figure 6.4 Installing the Attic Shield Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 40: Install Attic Insulation Shield

    • Bend all tabs inward 90º around the top of the shield. These tabs must be used to prevent blown insulation from getting between the shield and vent pipe, and to maintain air space clearance. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 41: Appliance Preparation

    The heat shield must remain in the vertical position. 2 SCREWS Figure 9.3 Replace the two screws as shown. Figure 9.6 Remove the insulation from the outer vent pipe. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 42: Rear Vent

    Use two self- tapping screws to secure gasket to outer wrap. Figure 9.9 Cut the metal retaining band and fold the sides out. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 43: Securing And Leveling The Appliance

    • Secure the appliance to the framing by using nails or screws through the nailing tabs. • Secure the appliance to the fl oor by inserting two screws through the pilot holes at the bottom of the appliance. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 44: Installing Vent Pipe (Dvp And Slp Pipe)

    fl ue at the horizontal elbow joint to prevent the elbow from rotating. Use screws no longer than 1/2 in. (13 mm). If predrilling screw holes, DO NOT penetrate inner pipe. INCORRECT Figure 10.4 Seams Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 45: Assemble Vent Sections (Slp Pipe Only)

    • Only outer pipes are sealed, sealing the inner fl ue is not required. • All unit collar, pipe, slip section, elbow and cap outer fl ues shall be sealed. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 46: Secure The Vent Sections

    Figure 10.10 Rotate Seams for Disassembly connection point to appliance. Figure 10.11 Align and Disassemble Vent Sections Figure 10.8 Securing Vertical Pipe Sections Figure 10.9 Securing Horizontal Pipe Sections Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 47: Install Decorative Ceiling Components (Slp Only)

    fl aps and the roof. WARNING! Risk of Fire! Clean out ALL materials from Figure 10.13 inside the support box and complete the vertical vent run and termination. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 48: Install Metal Roof Flashing

    • Caulk the perimeter of the fl ashing where it contacts the roof surface. See Figure 10.15. Figure 10.17 Assembling the Storm Collar Around the Pipe Figure 10.17 Assembling the Storm Collar Around the Pipe Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 49: Install Vertical Termination Cap

    • Once the pipe section and the termination cap have been connected, slide the wall thimble up to the interior wall surface and attach with screws provided. See Figure 10.19. Figure 10.19 Wall Thimble Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 50: Install Horizontal Termination Cap (Dvp And Slp Pipe)

    DVP-TRAP1 can adjust 1-1/2 in. (3-1/8 to 4-5/8) DVP-TRAP2 can adjust 4 in. (5-3/8 to 9-3/8) DVP-HPC1 can adjust 2-1/8 in. (4-1/4 to 6-3/8) DVP-HPC2 can adjust 4-1/8 in. (6-3/8 to 10-1/2) Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 51: Gas Information

    fl exible gas connector are connected to the 1/2 in. (13 mm) control valve inlet. • If substituting for these components, please consult local codes for compliance. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 52: Electrical Information

    Wiring for optional Hearth & Home Technologies approved accessories should be done now to avoid reconstruction. Follow instructions that come with those accessories. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 53 ORANGE 3 VAC WHITE GROUND TO FIREPLACE PLUG IN CHASSIS WIRES BATTERY PACK (TO BROWN) REMOTE PLUG IN VALVE Figure 12.3 Intellifi re Ignition Wiring Diagram with Remote Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 54: Electrical Service And Repair

    WARNING! Risk of Shock! Label all wires prior to dis- insulation. connection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 55: Junction Box Installation

    Figure 12.6 Junction Box Wired to Wall Switch or BC10 (1/4 in. male) as shown. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 56: Finishing

    TOP SLOT Figure 13.2 Step 3. Crease fl aps on left and right sides of splatter guard Figure 13.5 using the scored line as the guide. See Figure 13.3. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 57 Carefully grab splatter guard on or near the vertical center on the left and right sides. Pull outward gently, but fi rmly, Figure 13.8 taking care not to tear or remove the inserted tabs. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 58: Mantel And Wall Projections

    3 FT. MAXIMUM Note: Clearance from opening to perpendicular wall. Figure 13.13 Combustible Mantel Leg or Wall Projections (Acceptable on both sides of opening) NON-COMBUSTIBLE ZONE Figure 13.15 Non-Combustible Zone Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 59: Facing Material

    COMBUSTIBLE - TOP AND SIDES 0 IN. 0 IN. 0 IN. HIGH TEMPERATURE SEALANT (300° F/149° C MIN.) TOP AND SIDE SEAL JOINT Figure 13.16 Noncombustible Facing Diagram Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 60: Doors

    (Includes 1/8 in. opening each side of door) Finishing material between 1 and 4 inches thick. Refer to Table 1 for X and Y dimensions. Figure 13.20 Operable Hinge Door (Halston) Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 61: Elevated Hearth Systems

    Note 1. Add dimensions to Wall Penetration (Figure 8.2) and Rough Opening Height (Figure 5.2). Note 2. Verify Marble Cut Lengths on site prior to cutting. Note 3. Dimensions assume use of a 3/4 in. Hearth Pad. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 62: Appliance Setup

    Figure 14.2 Detail of Fan Wiring with Rheostat PORT HOLES IN CIRCLED AREA SHOULD BE COVERED WITH EMBER MATERIAL. NO OTHER PORT HOLES MAY COME INTO CONTACT WITH EMBER MATERIAL. Figure 14.4 Placement of Embers Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 63: Install The Log Assembly

    B as shown in Figure 5. When properly positioned, Log #1 will touch Tab B and sit on Log Rest. See Figure 4 to reference the position of Tab B and the log rest . 2158-935 Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 64 #2 with the log groove on Log #3. See Figure 9. Apply the supplied lava rock on fi rebox bottom as shown in Figure 10. Consult Owner’s Manual for Ember Placement instructions. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 65: Fixed Glass Assembly

    • Use non-combustible materials to cover the gap between Models the sheet rock and the appliance (when applicable to SL-550BE-B 1/8 in. 3/16 in. model). SL-550BE-IPI-B Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 66: Troubleshooting

    Take a reading at the thermopile leads. The reading should be 350 millivolts minimum. Replace the thermopile if the read- ing is below the minimum. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 67 Ensure that the glass is tightened properly on the unit, particularly on top corners. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 68: Intellifi Re Ignition System

    Verify module is securely grounded to metal chassis of appliance. D. Module voltage output / Valve/Pilot Verify battery voltage is at least 2.7 volts. Replace batteries if volt- solenoid ohms readings. age is below 2.7. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 69 ON position. If there is no spark at “I” terminal module must be replaced. If there is a spark at “I” terminal, module is fi ne. Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 70: Reference Materials

    Ø GAS LINE ACCESS ELECTRICAL ACCESS Location Inches Millimeters Location Inches Millimeters 16-3/8 27-3/16 25-3/4 12-7/8 15-7/8 3-1/2 6-5/8 6-7/8 34-3/8 2-3/16 36-1/2 8-3/4 Figure 16.1 Appliance Dimensions Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 71: Vent Components Diagrams

    14 in. (356 mm) 5 in. 12 in. (127 mm) (305 mm) 6 in. (152 mm) DVP-HVS (Vent Support) DVP-WS (Wall Shield Firestop) Figure 16.2 DVP vent components Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 72 79 mm 117 mm Length DVP-TRAP 5-3/8 in. 9-3/8 in. Trap2 Horizontal Termination Cap 137 mm 238 mm DVP-TRAP2 DVP-TRAP1 DVP-TRAPK2 DVP-TRAPK1 DVP-HPC1 DVP-HPC2 Figure 16.3 DVP vent components Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 73 13-7/8 in. 9-1/2 in. 26 in. (352 mm) (241 mm) 660 mm 14 in. (356 mm) DVP-HSM-B Extended Heat Shield DRC-RADIUS Figure 16.4 DVP vent components Cap Shield Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 74 1 in. (25 mm) (222 mm) 7-3/4 to 10-3/8 in. (197 to 264 mm) 1-5/8 in. (41 mm) DVP-FBHT FireBrickTermination Cap DVP-HPC High Performance Cap Figure 16.5 DVP vent components Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 75 (381 mm) 267 mm 10-7/8 in. 276 mm SLP-HRC-SS SLP-HRC-ZC-SS HORIZONTAL TERMINATION CAP DVP-TB1 DVP-TB1 SL-2DVP SLP90 ASSEMBLY DVP-TB1 HORIZONTAL TERMINATION CAP Figure 16.7 SLP Series Vent Components Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 76 2 - 12 51 - 305 SLP-FLEX-2 SLP-FLEX-3 SLP-FLEX-5 1524 SLP-FLEX-10 3048 SLP-HVS SLP-FS SLP-WS Horizontal Pipe Ceiling Firestop Wall Shield Firestop Support Figure 16.8 SLP Series Vent Components Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 77 26 in. 660 mm DVP-HSM-B DVP-2SL SL-2DVP Extended Heat Shield Adapter Adapter SLP-DCF-BK SLP-WT-BK Ceiling Firestop Wall Thimble-Black Black SLP-FLEX-TRAP Horizontal Termination Kit Figure 16.9 SLP Series Vent Components Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 78 B. Vent Components Diagrams (continued) COAXIAL to COLINEAR VENTING LINK-DV30B DV-46DVA-GCL Flex Liner Kit Coaxial/Colinear Appliance Connector DVP-2SL Adapter Figure 16.10 Coaxial to Colinear Vent Components Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...
  • Page 79: Service Parts List

    6748942, 6769426, 6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending. Printed in U.S.A. - Copyright 2009 Heat & Glo • SL-550BE-B, SL-550BE-IPI-B • 2158-900 Rev. H • 8/09...

This manual is also suitable for:

Sl-550be-ipi-b

Table of Contents