http://www.xiaoyu163.com SPECIFICATIONS -1/1 3 7 63 1515 0 Power supply 120 V AC, 60 Hz NOTE Power consumption 16 W This equipment has been tested and found to comply with Power consumption in standby mode the limits for a Class B digital device, pursuant to Part 15 1.4 W of the FCC Rules.
http://www.xiaoyu163.com PROTECTION OF EYES FROM LASER BEAM DURING SERVICING -1/1 3 7 63 1515 0 This set employs laser. Therefore, be sure to follow carefully the CAUTION instructions below when servicing. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous WARNING! radiation exposure.
http://www.xiaoyu163.com ACCESSORIES PARTS LIST -1/1 = ! SAFTY PARTS = Components marked All components used on this model at the production line are shown in this service manual. 3 7 63 1515 0 However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
http://www.xiaoyu163.com DISASSEMBLY - DISASSEMBLY -1/2 3 7 63 1515 0 CAUTION BEFORE STARTING SERVICING Electronic parts are susceptible to static electricity and may easily damaged, so do not forget to take a proper ground- ing treatment as required. Many screws are used inside the unit. To prevent missing, dropping, etc. of the screws, always use a magnetized screw driver in servicing.
http://www.xiaoyu163.com DISASSEMBLY - DISASSEMBLY -2/2 3 7 63 1515 0 CIRCUIT BOARD DISASSEMBLY Note: Before removing the main circuit board, be sure to shortcircuit the laserdiode output land. After replacing the main circuit board, open the land after inserting the flexible connector. (Refer to Mechanism Disassembly) 1.
http://www.xiaoyu163.com ELECTRICAL PARTS LIST -1/10 = ! SAFTY PARTS = Components marked All components used on this model at the production line are shown in this service manual. 3 7 63 1515 0 However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Page 9
http://www.xiaoyu163.com ELECTRICAL PARTS LIST -2/10 = ! SAFTY PARTS = Components marked All components used on this model at the production line are shown in this service manual. 3 7 63 1515 0 However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Page 10
http://www.xiaoyu163.com ELECTRICAL PARTS LIST -3/10 = ! SAFTY PARTS = Components marked All components used on this model at the production line are shown in this service manual. 3 7 63 1515 0 However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Page 11
http://www.xiaoyu163.com ELECTRICAL PARTS LIST -4/10 = ! SAFTY PARTS = Components marked All components used on this model at the production line are shown in this service manual. 3 7 63 1515 0 However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Page 12
http://www.xiaoyu163.com ELECTRICAL PARTS LIST -5/10 = ! SAFTY PARTS = Components marked All components used on this model at the production line are shown in this service manual. 3 7 63 1515 0 However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Page 13
http://www.xiaoyu163.com ELECTRICAL PARTS LIST -6/10 = ! SAFTY PARTS = Components marked All components used on this model at the production line are shown in this service manual. 3 7 63 1515 0 However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Page 14
http://www.xiaoyu163.com ELECTRICAL PARTS LIST -7/10 = ! SAFTY PARTS = Components marked All components used on this model at the production line are shown in this service manual. 3 7 63 1515 0 However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Page 15
http://www.xiaoyu163.com ELECTRICAL PARTS LIST -8/10 = ! SAFTY PARTS = Components marked All components used on this model at the production line are shown in this service manual. 3 7 63 1515 0 However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Page 16
http://www.xiaoyu163.com ELECTRICAL PARTS LIST -9/10 = ! SAFTY PARTS = Components marked All components used on this model at the production line are shown in this service manual. 3 7 63 1515 0 However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
http://www.xiaoyu163.com ELECTRICAL PARTS LIST -10/10 • Regarding connectors, they are not stocked as they are not the initial order items. 3 7 63 1515 0 The connectors are available after they are supplied from connector manufacturers upon the order is received. CHIP RESISTOR PART CODE Chip Resistor Part Coding Figure...
http://www.xiaoyu163.com WIRING -3/6 (JACK C.B) 3 7 6 3 1 5 1 5 0 JK602 SW602 VIDEO S-VIDEO OUTPUT COMPONENT VIDEO OUT/ PROGRESSIVE SCAN JK601 COMPONENT/ VIDEO OUT PROGRESSIVE SCAN DIGITAL OUT DIGITAL JACK C.B AUDIO OUT2 L AUDIO OUT1 L (OPTICAL) Pr/Cr (COAXIAL)
http://www.xiaoyu163.com VOLTAGECHART -1/3 3 7 6 3 1 5 1 5 0 MODE MODE MODE MODE MODE MODE MODE MODE MODE MODE PLAY PLAY PLAY PLAY PLAY PLAY PLAY STOP PLAY STOP PLAY STOP PLAY PIN NO. PIN NO. PIN NO. PIN NO.
Page 37
http://www.xiaoyu163.com VOLTAGECHART -2/3 3 7 6 3 1 5 1 5 0 MODE MODE MODE MODE MODE MODE STOP PLAY STOP PLAY STOP PLAY STOP PLAY PLAY PLAY PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. I C 3 0 5 I C 3 F 1 I C 4 0 1...
http://www.xiaoyu163.com VOLTAGECHART -3/3 3 7 6 3 1 5 1 5 0 MODE MODE MODE MODE MODE MODE MODE MODE MODE MODE STOP PLAY STOP PLAY PLAY PLAY PLAY PLAY PLAY STOP PLAY STOP PLAY STOP PLAY PIN NO. PIN NO. PIN NO.
Page 42
http://www.xiaoyu163.com IC BLOCK DIAGRAM -2/4 3 7 63 1515 0 IC, GMS81C2012-HI013 High Voltage Port ADC Power Supply R03/BUZO R02/EC0 R01/INT1 R00/INT0 Vdisp/RA R10~R17 R20~R27 R30~R35 Driver Buzzer Stack Pointer Data Memory (448 bytes) Program Memory Interrupt Controller Data Table 8-b it B a sic S ystem controller In terval...
http://www.xiaoyu163.com IC DESCRIPTION -1/3 (HD153702TF -1/2) 3 7 63 1515 0 Pin No. Pin Name Description Not connect RFIN RF differential input terminal RFIP SUMF SUM RF input /DC filter connection terminal for SUM differential amplifier AGHPF The high path filter connection terminal for AGC AGFR The filter connection terminal for AGC AGFI...
Page 46
http://www.xiaoyu163.com IC DESCRIPTION -1/3 (HD153702TF -2/2) 3 7 63 1515 0 Pin No. Pin Name Description GND_SRV Ground connection terminal (SERVO system) The monitor diode input terminal of APC1 The laser diode output terminal of APC1 IREFT The external resistance connection terminal for setting up servo system standard current VREF1 Servo system standard bias voltage output terminal DVD4D input terminal...
Page 47
http://www.xiaoyu163.com IC DESCRIPTION -2/3 (M12L16161A-7T -1/2) 3 7 63 1515 0 Pin No. Pin Name Description 3.3 V is applied. (VCC is for the internal circuit.) Data is input and ouput from these pins. These pins are the same as those of a conventional DRAM.
Page 48
http://www.xiaoyu163.com IC DESCRIPTION -2/3 (M12L16161A-7T -2/2) 3 7 63 1515 0 Pin No. Pin Name Description This pin determines whether or not the next CLK is valid. If CKE is High, the next CLK rising edge is valid. If CKE is Low, the next CLK rising edge is invalid. This pin is used for power- down and clock suspend modes.
Page 49
http://www.xiaoyu163.com IC DESCRIPTION -3/3 (HDC25D811B -1/6) 3 7 63 1515 0 Pin No. Pin Name Description DAT0 bi-directional data to DRAM DAT1 bi-directional data to DRAM DAT2 bi-directional data to DRAM DAT3 bi-directional data to DRAM DAT4 bi-directional data to DRAM DAT5 bi-directional data to DRAM DAT6...
Page 50
http://www.xiaoyu163.com IC DESCRIPTION -3/3 (HDC25D811B -2/6) 3 7 63 1515 0 Pin No. Pin Name Description TESTOUT1 TEST OUT (Default 0) TESTOUT2 TEST OUT (Default 0) TESTOUT3 TEST OUT (Default 0) TESTOUT4 TEST OUT (Default 0) TESTOUT5 TEST OUT (Default 0) TESTOUT6 TEST OUT (Default 0) TESTOUT7...
Page 51
http://www.xiaoyu163.com IC DESCRIPTION -3/3 (HDC25D811B -3/6) 3 7 63 1515 0 Pin No. Pin Name Description CAPT2 DAC Top Coupling Cap Port for DAC 2 AOUT1 SERVO D/A OUT1 AGND AGND : DAC10BIT AGND AGND : DAC10BIT CAPT1 DAC Top Coupling Cap Port for DAC 1 AOUT0 SERVO D/A OUT0 CAPT0...
Page 52
http://www.xiaoyu163.com IC DESCRIPTION -3/3 (HDC25D811B -4/6) 3 7 63 1515 0 Pin No. Pin Name Description GND : PLL ADAT Audio DAC Audio data Output BCLK Audio DAC FS48 Output EXCK CD Sub Data Request clock AGND AGND : PLL SQCK CD SubQ data Request clock AVDD...
Page 53
http://www.xiaoyu163.com IC DESCRIPTION -3/3 (HDC25D811B -5/6) 3 7 63 1515 0 Pin No. Pin Name Description 6 bit ADC channel Input 6 bit ADC Center voltage 6 bit ADC bottom voltage Spindle motor control signal Spindle motor control signal Spindle motor ON/OFF control signal FG_M Spindle FG input ZINT...
Page 54
http://www.xiaoyu163.com IC DESCRIPTION -3/3 (HDC25D811B -6/6) 3 7 63 1515 0 Pin No. Pin Name Description SDCLK / MPEG data transfer clock / CD : C16M SERR / S MPEG data error detection signal / CD : SYNC / D MPEG data sector sync.
http://www.xiaoyu163.com MECHANICAL, MECHANISM PARTS LIST -1/1 = ! SAFTY PARTS = Components marked All components used on this model at the production line are shown in this service manual. 3 7 63 1515 0 However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
http://www.xiaoyu163.com ELECTRICAL TROUBLESHOOTING GUIDE -1/10 3 7 63 1515 0 1. Power(SMPS) Circuit No 5V_D No FLD or 5V_A . Is 5.2VA section working? Is 5.2VA section working? (Is the POWER CTL at Pin6 High/low?) Is oscillation present at the Are D109, L103 open? Base of Q108? No 5.2VA.
Page 59
http://www.xiaoyu163.com ELECTRICAL TROUBLESHOOTING GUIDE -2/10 3 7 63 1515 0 2. µ-COM Circuit A. No Power POWER ON Do “Hello” appear at FLD? Is P3901 connected normally? Reconnect it. Check power. (Refer to power) If power is Does Logo appear normal on the screen? L 13942296513...
Page 60
http://www.xiaoyu163.com ELECTRICAL TROUBLESHOOTING GUIDE -3/10 3 7 63 1515 0 B. Audio abnormal C. Video abnormal AUDIO ABNORMAL VIDEO ABNORMAL Check Audio jack. Check Video jack. YES (If OK) YES (If OK) Refer to Audio part. Refer to Video part. YES (If OK) YES (If OK) Refer to Decoder part.
Page 61
http://www.xiaoyu163.com ELECTRICAL TROUBLESHOOTING GUIDE -4/10 3 7 63 1515 0 E. Picture abnormal PICTURE ABNORMAL Check the disc. Refer to Servo part If OK Check DSP YES (If OK) Check PANTERA YES (If OK) Replace B/D L 13942296513 F. Disc Error DISC ERROR Check Disc YES (If OK)
Page 62
http://www.xiaoyu163.com ELECTRICAL TROUBLESHOOTING GUIDE -5/10 3 7 63 1515 0 3. PANTERA Circuit Power is on Does Logo appear Check power & clock. on the screen? Does the Check CD/DVD DSP output moving picture of the DVD Disc Is PANTERA play on the screen data signal normal? signal.
Page 63
http://www.xiaoyu163.com ELECTRICAL TROUBLESHOOTING GUIDE -6/10 3 7 63 1515 0 4. Front Circuit (Digitron & key) START Power on. Is oscillation of Check Power. LED ON? X901 normal? Check waveform Is Digitron on normally? Replace IC902. of IC901 Pin 7. Do all the Is waveform of IC901 Check waveform...
Page 64
http://www.xiaoyu163.com ELECTRICAL TROUBLESHOOTING GUIDE -7/10 3 7 63 1515 0 5. RF/Servo Circuit CHECK POINT(General) Does signal goes "High" to IC201 Pin186 when the power is on? Does signal pulse Check "2.PANTERA Part". input to IC201 Pins 53, 54 when the powe is on? Does Replace X201 or IC206...
Page 65
http://www.xiaoyu163.com ELECTRICAL TROUBLESHOOTING GUIDE -8/10 3 7 63 1515 0 No disc .Power on Check loading Part. Push Pick-up to inner track to Does tray open or close? the end by hand. Does DECK assembly is defective. PMD03 Pin 6 change (Limit sw) high to low? Pressing...
Page 66
http://www.xiaoyu163.com ELECTRICAL TROUBLESHOOTING GUIDE -9/10 3 7 63 1515 0 DISC IN OPEN/CLOSE Fig.3. FOCUS ERROR waveform Check Check IC2A1 Pin 47,50,51,52 the focus error moving the FOCUS ON? lens up and down. in DVD Mode (IC2A1 Pin 39) IC201 no output : Pick-up is defective. Does the TTL level change at IC201 Replace IC201.
http://www.xiaoyu163.com DVD MECHANISM DISASSEMBLY -1/3 3 7 63 1515 0 (S2) TRAY DISC (S4) HOLDER CLAMP (S4) MOTOR ASSEMBLY TRAY PLATE CLAMP GEAR TRAY GEAR WHEEL TRAY (S1) (S1) (S1) PLATE CLAMP MAGNET CLAMP (H1) HOLDER CLAMP UPPER CLAMP BASE TRAY ROLLER BASE TRAY BASE TRAY (L2)
Page 70
http://www.xiaoyu163.com DVD MECHANISM DISASSEMBLY -2/3 3 7 63 1515 0 (L3) GEAR MIDDLE GEAR ASSEMBLY FEED GEAR ASSEMBLY RACK (S7) RUBBER REAR RUBBER DAMPER (S8) RUBBER REAR (S7) (S7) PICK UP ASSEMBLY GENERAL BASE PU(OUTSERT) (S7) (C7) RUBBER DAMPER PICK UP ASSEMBLY GENERAL GAER ASSEMBLY RACK MOTOR ASSEMBLY SPINDLE GEAR MIDDLE...
Page 71
http://www.xiaoyu163.com DVD MECHANISM DISASSEMBLY -3/3 3 7 63 1515 0 (S10) GEAR SLIDER GEAR MAIN (S12) Fig.(B) GEAR UP/DOWN GEAR EXCHANGE (S11) (S13) GEAR LOADING (S15) Fig.(C) MOTOR ASSEMBLY MAIN (S15) GEAR WHEEL MAIN (S14) BASE MAIN MOTOR ASSEMBLY MAIN (L4) (C9) (C8)
http://www.xiaoyu163.com OTHER PARTS LIST -1/1 = ! SAFTY PARTS = Components marked All components used on this model at the production line are shown in this service manual. 3 7 63 1515 0 However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.