Kenwood KDC-X5000BT Instruction Manual page 18

AUDIO SETTINGS
Crossover settings
Below are the available setting items for 2-way crossover and 3-way
crossover.
SPEAKER SIZE
Selects according to the connected speaker size for optimum
performance.
• The frequency and slope settings are automatically set for the
crossover of the selected speaker.
• If [NONE] is selected for [TWEETER] of [FRONT], [REAR] and [SUBWOOFER] for
[SPEAKER SIZE], the [X ' OVER] setting of the speaker is not available.
X ' OVER
[FRQ]/ [F - HPF FRQ]/ [R - HPF FRQ]/ [SW LPF FRQ]/ [HPF FRQ]/ [LPF FRQ]:
Adjusts the crossover frequency for the selected speakers (high pass
filter or low pass filter).
• If [THROUGH] is selected, all signals are sent to the selected speakers.
[F - HPF SLOPE]/ [R - HPF SLOPE]/ [SW LPF SLOPE]/ [HPF SLOPE]/ [LPF SLOPE]/
[SLOPE]:
Adjusts the crossover slope.
• Selectable only if a setting other than [THROUGH] is selected for the
crossover frequency.
[SW LPF PHASE]/ [PHASE]:
Selects the phase of the speaker output to be in line with the other
speaker output.
[GAIN LEFT]/ [GAIN RIGHT]/ [F - HPF GAIN]/ [R - HPF GAIN]/ [SW LPF GAIN]/ [GAIN]:
Adjusts the output volume of the selected speaker.
The following items is selectable only if [SUBWOOFER SET] is set to [ON]
( 15):
– [SUBWOOFER]/ [WOOFER] of [SPEAKER SIZE]
– [SUBWOOFER LPF]/ [WOOFER] of [X ' OVER]
16
2-way crossover setting items
SPEAKER SIZE
FRONT SIZE
TWEETER
REAR 8 CM/ 10 CM/ 12 CM/ 13 CM/ 16 CM/ 17 CM/18 CM/ 4×6/ 5×7/ 6×8/
6×9/ 7×10/ NONE (not connected)
SUBWOOFER 16CM/ 20CM/ 25CM/ 30CM/ 38CM OVER/ NONE (not connected)
X ' OVER
TWEETER FRQ
GAIN LEFT
GAIN RIGHT
FRONT HPF F - HPF FRQ
F - HPF SLOPE
F - HPF GAIN
REAR HPF R - HPF FRQ
R - HPF SLOPE
R - HPF GAIN
SUBWOOFER SW LPF FRQ 30HZ/ 40HZ/ 50HZ/ 60HZ/ 70HZ/ 80HZ/ 90HZ/
LPF 100HZ/ 120HZ/ 150HZ/ 180HZ/ 220HZ/ 250HZ/
THROUGH
SW LPF SLOPE –6DB/ –12DB/ –18DB/ –24DB
SW LPF PHASE REVERSE (180°)/ NORMAL (0°)
SW LPF GAIN –8 to 0
8CM/ 10CM/ 12CM/ 13CM/ 16CM/ 17CM/ 18CM/
4×6/ 5×7/ 6×8/ 6×9/ 7×10
SMALL/ MIDDLE/ LARGE/ NONE (not connected)
1KHZ/ 1.6KHZ/ 2.5KHZ/ 4KHZ/ 5KHZ/ 6.3KHZ/
8KHZ/ 10KHZ/12.5KHZ
–8 to 0
–8 to 0
30HZ/40HZ/ 50HZ/ 60HZ/ 70HZ/ 80HZ/ 90HZ/
100HZ/ 120HZ/ 150HZ/ 180HZ/ 220HZ/ 250HZ/
THROUGH
–6DB/ –12DB/ –18DB/ –24DB
–8 to 0
(Refer FRONT HPF settings above.)