Table of Contents
Advertisement
installation
|
10
GENERAL SAFETY INFORMATION
1. The appliance installation must conform with
local codes or in the absence of local codes,
with CAN/CGA B149 (in Canada) or the
National Fuel Gas Code ANSI Z223.1. This
appliance should be installed by a qualified
gas fitter technician only.
2. Installation and repair should be done by a
qualified service person.
3. The appliance should be inspected before use
and at least annually by a professional service
person. More frequent cleaning may be required
due to excessive lint from carpeting, bedding
material, animal hair, etc. It is imperative that
control compartments, burners and circulating
air passageways of the appliance be kept clean.
4. See general construction and assembly instruc-
tions. This appliance may only be installed in a
vented, noncombustible fireplace.
5. This appliance is Listed for bedroom installa-
tions. In Canada room heaters must be installed
with a Listed Millivolt Thermostat. Some areas
may have further requirements, check local
codes before installation.
6. This unit is not approved for installation into a
mobile home.
7. Always connect this insert to a vent system
venting to the outside of the building envelope.
Never vent to another room or inside a building.
Make sure that the vent is properly sized and is
of adequate height to provide the proper draft.
8. Inspect the venting system annually for blockage
and any signs of deterioration.
9. Any glass removed for servicing must be re-
placed prior to operating the appliance.
10. To prevent injury, do not allow anyone who is
unfamiliar with the operation to use the fireplace.
11. Failure to position the parts in accordance with
the diagrams in this manual or failure to use only
parts specifically approved with this appliance
may result in property damage or personal injury.
12. Due to high temperatures, the appliance should
be located out of high traffic areas and away
from furniture and draperies. Children and
adults should be alerted to the hazards of high
surface temperatures, especially the fireplace
glass and gold trims, and should stay away to
avoid burns or clothing ignition. Young children
should be carefully supervised when they are
in the same room as the appliance. Clothing or
other flammable material should not be placed
on or near the appliance.
Emissions from burning wood or gas could
contain chemicals known to the State of
California to cause cancer, birth defects or
other reproductive harm.
10 |
Regency U31-10 Gas Fireplace Insert
INSTALLATION
CHECKLIST
The Regency Gas Insert is installed as listed below.
1. Unit Location - check Clearances to Combus-
tibles.
2. Make the gas connections.
Convert to Propane Gas if necessary.
3. Install the flue or liner to the sliding draft hood.
4. Install Venting. Slide the unit into the fireplace.
Attach draft hood to the insert.
5. Test gas pressure.. Check aeration
6. Test for flue spillage.
7. Install the optional brick panels.
8. Install the log set.
9) Assemble and install the faceplate.
10) Install the glass front.
11) Install Safety Screen, Remote Control and
Optional Wall Thermostat.
12) Final check: Before leaving this unit with the
customer, the installer must ensure that the
appliance is firing correctly. This includes:
a)
Clocking the appliance to ensure the
correct firing rate.
b)
Adjusting the primary air, if required, to
ensure that the flame does not carbon.
c)
Ensuring that the appliance is venting
correctly.
MATERIALS REQUIRED
No electrical power supply is required for the gas
control to operate. A 120 Volt AC power cord is
hooked up to the fan. Plug the 3 wire cord into a
suitable receptacle. Do not cut the ground terminal
off under any circumstances. When connected
with 120 volts, the appliance must be electrically
grounded in accordance with local codes, or in the
absence of local codes, with the current Canadian
Electrical Code CSA C22.1 (in Canada) or with
the current National Electrical Code ANSI/NFPA
70-1987 (in U.S.A.).
NOTE: This unit is equipped with a heat sensor
thermodisc which will prevent the blower
from operating until the unit reaches the
correct temperature.
Advertisement
Table of Contents
