Set Up; Ride Height; Shock Springs - THUNDER TIGER Hammer S18 Instruction Manual

18 SET UP 設定
Front & Rear Camber 前後輪傾斜角調整
a. Use a 2.5mm Allen wrench as shown to adjust the front & rear camber.
b. Turning the upper pivot ball clockwise increases camber towards the
negative side; turning it counter-clockwise increases camber towards the positive
side.
a. 使用2.5mm六角扳手調整前、後輪傾斜角（如圖示）。
b. 調整上輪軸球頭順時針旋轉將增加負傾斜角；調整上輪軸球頭逆時針旋轉將增加正
傾斜角。
請參照本說明調整您愛車前、後輪的傾角。
Ride Height 調整車身高度
a. The truck ride height can be increased by adding preload clips to the shocks.
Removing preload clips will decrease the ride height.
b. Compress the spring and insert the preload clips between the spring collar and
the shock body flange.
a. 車身高度可利用避震器調整墊片改變。增加調整墊片可增加車高；減少墊片則降低
車高。
b. 安裝或拆卸墊片時，請壓縮避震器彈簧再置入或取出墊片即可。
Hard Suspension
懸吊較硬
Slipper Clutch 扭力限制器調整
a. Use a 8mm nut driver to adjust the slipper clutch.
b. Tighten the slipper nut until the spring is fully compressed.
c. Once you've reached the point where the spring is fully compressed, loosen the
slipper nut 1/4turn.
d. Do not run you truck with the slipper nut any looser than 1/4turn from full spring
compression. Setting the slipper too loose may result in a damaged spur gear.
a. 使用8mm扳手調整扭力限制器。
b. 將螺絲上緊至彈簧完全壓縮。
c. 彈簧完全壓縮後，再將螺帽轉鬆1/4圈。
c. 請勿將固定螺帽鬆脫超過1/4圈，避免造成大主齒損壞。
Shock Springs 避震器彈簧搭配
Stiffer springs will give you better handling and higher cornering speed on smooth surfaces such as asphalt, concrete, and hard
pack dirt. Soft springs are better for rougher terrain, rock crawling and jumping. Softer springs will increase the rollover tendency
of the truck at higher speeds.
較硬的避震器在平坦堅硬的跑道上（例如柏油路面），將可提供較好的操控性與過彎速度。較軟的避震器適合於崎嶇不平的路面
（例如碎石地）以及跳躍動作，並且可以降低翻車的機率。
6mm
4mm
Part Number Spring Color
產品編號 彈簧顏色
PD8088 Blue(Std) 藍
PD8120 Gold 金
PD8121 Red 紅
PD8122 Bronze 銅
2mm
1mm
Soft Suspension
懸吊較軟
Spring Rate Relative Stiffness
彈性係數 相對軟硬度
0.0473kgf/mm Softest
0.0551kgf/mm
0.0639kgf/mm
0.0736kgf/mm Stiffest
Add Add
Pos. Neg.
Camber Camber
Loosen
Tighten
Slipper
Slipper
Clutch
Clutch
最軟
最硬