Charging The Glow Plug Igniter 電夾充電方式 4; Preparing The Radio 遙控器使用準備 4; Radio Battery Installation 遙控器電池安裝 4 - THUNDER TIGER Hammer S18 Instruction Manual

1
CHARGING THE GLOW PLUG IGNITER 電夾充電方式
a
a. Plug the charger into an AC outlet, and then pull on the igniter lever to accept the charging adapter.
b. At this point, the small red LED indicator on the charger should light up indicating the charging sequence is in progress.
c. When the charging complete, pull on the glow plug igniter lever to unplug the glow igniter. Charge the new glow plug igniter for
16 to 24 hours on the first charge. For subsequent charges, charge it about 12 hours before next use.
NOTE: If the igniter gets warm or hot during the charge, unplug the igniter from charger immediately. A warm / hot igniter means
the igniter is overcharged. Overcharging can damage the internal battery in the igniter; thus, shortening its life.
a. 將充電器插入家用110V插座中，再接上電夾
b. 充電過程中，紅色LED燈會保持亮的狀態，如不亮表示為短路，電池無法充電
c. 充電完成，將充電器自插座拔下，再分開電夾；新電夾首次充電時間需16到20小時，之後只需充大約12小時即可
注意：充電過程中，電夾電池如出現高溫現象(40~45°C)，表示已過度充電，需立即停止充電。過度充電容易造成電池損壞，更可能
產生爆炸起火，請謹慎使用。
2
PREPARING THE RADIO 遙控器使用準備
a
a. Check the frequency printed on the transmitter crystal.
b. Remove the radio receiver from box. Check the frequency printed on the receiver crystal, and make sure it matches with the
transmitter crystal. Make sure no one will operate on the same frequency when you are. When there is a radio glitch, it will most
likely be caused by improper crystal, damaged crystal, or people operating on the same frequency. Ensure all wires are securely
connected to the receiver:
steering servo connector plug - into the channel 1 slot 連接孔1 (CH1)—轉向伺服機
throttle servo connector plug - into the channel 2 slot 連接孔2 (CH2)—油門伺服機
battery switch connector plug - into battery slot. 電池連接孔 (BATT)—接收機電池
Then thread the receiver antenna/wire through the antenna mount. Thread the receiver antenna/wire all the way through the antenna
tube and install the antenna tube onto the mount. After checking, place the receiver back in the box and secure the receiver box
top.
c. Install the antenna into transmitter.
a. 檢查發射機頻率。
b. 檢查接收機晶體頻率，確認發射機與接收機頻率是否相同。大部份搖控器會失靈可能都是頻率造成或附近有人使用相同的操控頻
率。並確認所有的電子接線都牢固，且依序連結在接收機的連結插孔，確認完畢後，將接收機放回接收機盒並且安全的固定好。
c. 裝上發射機天線。
3
RADIO BATTERY INSTALLATION 遙控器電池安裝
a
a. Install 8 AA size alkaline batteries into transmitter.
b. Install 4 AA size alkaline batteries in receiver battery box to the receiver switch.
c. Install the battery into the receiver box, secure the box with a body clip.
a. 安裝8顆3號電池於發射機上，請注意正負極正確安裝方向。
b. 安裝4顆3號接收機電池於電池盒上，並連接接收機電源線、開關線，請注意正、負極正確安裝方向。
c. 將接收機電池安裝於接收盒中並使用R型插銷固定。
b
b
b
c
c
c