Yamaha QL5 Reference Manual page 197

FUNCTION PARAMETER 1 PARAMETER 2
SELECTED CH VIEW —
OVERVIEW —
HOME
TOGGLE —
PEAK HOLD ON —
METER
SURROUND METER —
PROGRAM CHANGE PGM 1–128
CC 1–31, 33–95,
CONTROL CHANGE
102–119
MIDI
NOTE ON C-2 (0)
NOTE ON :
NOTE ON G 8 (127)
OUTPUT —
SELECTED CH ASSIGN —
DIMMER ON —
STEREO L/R
MONO (C)
LCR
SOURCE SELECT
PB OUT
MONITOR
*5)
DEFINE
SURROUND SOURCE
*6)
SELECT
SURROUND
STEREO, MONO
DOWNMIX
SOLO
SURROUND SPEAKER
L, R, C, Ls, Rs, LFE
Explanation
Displays the SELECTED CHANNEL VIEW screen.
Displays the OVERVIEW screen.
Each press of the key will alternately display the
SELECTED CHANNEL VIEW screen and the
OVERVIEW screen.
Turns the meter's peak hold function on/off. Lit
when on.
For Surround mode, toggle between the
content to be shown in meters displayed in the
Function Access Area. The lamp is off for MIX 1-
6, and on for SURROUND MONITOR.
Transmit the corresponding MIDI message.
For NOTE ON, it goes OFF when the bank is
switched.
Switch the monitor output on/off.
While holding down this key, press the SEL key
of a MIX or MATRIX channel to switch the
assignment on/off. During this time, the [SEL]
LED will be lit if assign is ON, or dark if OFF.
The assignment setting made while holding
down this key will be stored. Pressing the key
again will recall the stored setting. Settings can
be stored in multiple keys to facilitate rapid
assignment switching. It goes OFF when the
bank is switched.
Enable the dimmer and attenuate the monitor
signal.
Recall the selected signal to the monitor.
Recall the selected signal to the surround
monitor.
When this function is off (the lamp is off),
the setting returns to 5.1 monitor.
When this function is on (the lamp is on),
the SURROUND MONITOR screen opens.
When this function is off (the lamp is off),
the SURROUND MONITOR screen closes.
This functionality is the same as the
SPEAKER MUTE function in the
SURROUND MONITOR screen. When the
SOLO button is on, it functions as a SOLO
key.
197
FUNCTION PARAMETER 1 PARAMETER 2
MUTE GROUP 1
: —
MUTE
MUTE GROUP 8
MASTER
ALL MUTE —
GO TO PROJECT START
GO TO PREV MARKER
REWIND
FAST FORWARD
GO TO NEXT MARKER
TRANSPORT GO TO PROJECT END
CYCLE
NUENDO
STOP
LIVE
START
REC
EASY RECORDING
PEAK CLEAR —
ADD MARKER —
OSCILLATOR ON —
SELECTED CH ASSIGN —
OSCILLATOR
DIRECT ASSIGN *1)
BOOKMARK —
PAGE
CHANGE
BOOKMARK with "SEL" —
PREVIOUS PAGE
—
NEXT PAGE
CLOSE POPUP —
PLAY/PAUSE, STOP,
FF/NEXT,
REW/PREVIOUS, REC
RECORDER TRANSPORT
AUTO REC
REC & START
Setup
Explanation
Switch MUTE GROUP MASTER on/off.
Turns all MUTE GROUP MASTER settings on/off
together.
Operate the transport functions of Nuendo Live.
Clear the peak indicators of the Nuendo Live
screen.
This function executes ADD MARKER of
NUENDO Live.
Switch the OSC on/off.
While holding down this key, press a SEL key of a
channel to switch the assignment on/off. During
this time, the [SEL] LED will be lit if assign is ON,
or dark if OFF. It goes OFF when the bank is
switched.
Assign the oscillator to the channel selected
from list 1).
Memorize the currently-selected screen (hold
down the key for two seconds or longer), or
display the last-memorized screen (press and
release the key within two seconds). Popup
windows can also be memorized. In the case of
a rack, the number of that rack is also
memorized.
Memorize the above BOOKMARK with the
addition of the SEL status.
Display the previous/next page.
Close the displayed window.
Recorder transport functions.
Shortcut function for STOP  REC  PLAY.
Recording will be initiated in a single action. If
this is executed during recording, the file being
recorded will first be closed, and then recording
will continue with a new file.
Start recording immediately without entering
record-ready mode.
Reference Manual