Seat Assembly; Cable Assembly - Weider WEEVSY1975.0 User Manual

11. Grease an M10 x 51mm Bolt (66). Attach a Cable
Pivot (39) to the Right Arm (9) with the Bolt and
an M10 Nylon Locknut (56). Do not overtighten
the Locknut; the Cable Pivot must be able to
pivot easily.
Wet the inside of a Large Foam Pad (42) with
soapy water. Slide the Large Foam Pad onto the
Right Arm (9).
Attach the lower end of a Handle (11) to the Right
Arm (9) with an M10 x 45mm Button Bolt (77) and
an M10 Large Washers (80). Press a 50mm
Round Handle Cap (31) into the Right Arm. Do
not tighten the Bolt yet.
Attach the upper end of the Handle (11) to the
Right Arm (9) with an M10 x 67mm Button Bolt
(71), two M10 Washers (57), two 12mm Spacers
(52), and an M10 Nylon Locknut (56). Tighten
the M10 x 45mm Button Bolt (77).
Assemble the Left Arm (10) in the same
manner.
12. Grease an M10 x 85mm Bolt (67) and two Arm
Bushings (44). Attach the Right Arm (9) to the
Pivot Frame (5) with the Bolt, two M10 Washers
(57), the two Arm Bushings, and an M10 Nylon
Locknut (56). Do not overtighten the Locknut;
the Arm must be able to pivot easily.
Attach the Left Arm (10) to the Pivot Frame (5)
in the same manner.

Cable Assembly

13. Refer to the CABLE DIAGRAMS on page 20 as
you assemble the cables and to identify the
cables.
Locate the Arm Cable (54). Grease an M8 x
22mm Shoulder Bolt (65). Attach the Cable to the
indicated Cable Pivot (39) with the Bolt and an
M8 Nylon Locknut (58). Make sure that the
Cable can pivot easily around the Bolt.
11
56
66
57 Grease
52
9
39
52
57
71 10
56
11
42
80
31
77
12
67
Grease
5
57
44
9
44
57
56
Grease
13
58
39
54
Grease
65
10

Seat Assembly

30. Attach the Backrest (16) to the Upright (3) with
two M6 x 63mm Screws (70) and two M6
Washers (82).
31. Attach the Seat (15) to the Seat Frame (6) with
two M6 x 63mm Screws (70) and two M6
Washers (82).
32. Attach the Lock Plate (73) to the Front Leg (7)
10
with an M10 x 70mm Bolt (86), an M10 Washer
(57), and an M10 Nylon Locknut (56). Do not
overtighten the Locknut; the Lock Plate must
be able to pivot easily.
Attach the Leg Lever Pin (38) to the Front Leg (7)
with an M4 x 20mm Self-tapping Screw (69).
Insert the Leg Lever Pin through the Leg Lever
(8) and the Lock Plate (73).
33. Insert the Pad Tube (29) through the Front Leg
(7). Slide two Small Foam Pads (28) onto the
ends of the Pad Tube. Press two Foam Caps (34)
onto the Pad Tube.
Slide two Small Foam Pads (28) onto the Leg
Lever (8). Press two Foam Caps (34) onto the
Leg Lever.
30
3
70
82
70
82
16
31
15
6
82
82
70
70
32
56 57
69
38 73
86
8
7
33
34
29
28
34
28
28
8
15
34