Mitel 3300 Configuration Notes
  1. Manuals
  2. Brands
  3. Mitel Manuals
  4. Network Hardware
  5. 3300
  6. Configuration notes

Mitel 3300 Configuration Notes

Pbx interface with conferencing server
Hide thumbs Also See for 3300:
Table of Contents

Advertisement

Quick Links

See also: Technician's Handbook , Reference Manual
Mitel PBX interface with Conferencing Server
Configuration Notes
Note: This document section is maintained by Mitel Networks
When referring to any information in this document please also check the
Additions & Correction section on the last page for updates.
File: Mitel 3300 PBX interface with Conferencing Server V002
7/4/2004
Page 1 of 22

Advertisement

Table of Contents
loading

Related Manuals for Mitel 3300

Summary of Contents for Mitel 3300

  • Page 1: Mitel Pbx Interface With Conferencing Server Configuration Notes

    Note: This document section is maintained by Mitel Networks When referring to any information in this document please also check the Additions & Correction section on the last page for updates. File: Mitel 3300 PBX interface with Conferencing Server V002 7/4/2004 Page 1 of 22...

  • Page 2: Table Of Contents

    Mitel PBX interface with Conferencing Server Configuration Notes ...1 Introduction...3 3300ICP with ISDN or SX2000 with ISDN...3 Example of T1 PRI programming on 3300 or SX2000...3 Class Of Service – changes from default values ...3 Link Descriptor Assignment...4 Digital Link Assignment ...4 MSDN-DPNSS-DASSII Trunk Circuit Descriptor...5...

  • Page 3: Introduction

    This document describes the configuration of Mitel Networks PBX’s to correctly interface to the Interactive Group Communication System by VCon. For more information on the configuration of the IGC, please refer to Mitel 3300 - RemoteAbility IGC Integration Specifications V1. Note that all PBX configuration should be undertaken by a qualified Technician.

  • Page 4: Link Descriptor Assignment

    ANI/DNIS/ISDN Number Delivery Link Descriptor Assignment Number: Address for Message Control: BER - Maintenance Limit, 10**-n: BER - Service Limit, 10**-n: Data Call Alternate Digit Inversion: Framing Losses in 24 hrs - Maintenance Limit: Framing Losses in 24 hrs - Service Limit: Integrated Digital Access: Satellite Link Delay: Slip Rate - Maintenance Limit (slips/24hr.):...

  • Page 5: Msdn-Dpnss-Dassii Trunk Circuit Descriptor

    Cabinet: Shelf: Slot: Circuit: Card Type: Trunk Number: Trunk Service Number: DTS Service Number: Circuit Descriptor Number: Interconnect Number: 3300 ICP with T1/D4 or SX2000 with T1/D4 Dual Far End Seizure Connection Priority Incoming Local Office ISDN Trunk UNIVERSAL T1...

  • Page 6: Example Of T1/D4 (Cas) Programming On 3300 Or Sx2000

    **Note: The Dialogic card in the IGC server is expecting ANI on the T1D4 trunk, but the 3300 or SX2000 does not deliver ANI over T1D4. This will result in a 10 to 15 second delay in accessing the IGC after the trunk access number is dialed.

  • Page 7: Link Descriptor Assignment

    ANI/DNIS/ISDN Number Delivery Link Descriptor Assignment Number: Address for Message Control: BER - Maintenance Limit, 10**-n: BER - Service Limit, 10**-n: Data Call Alternate Digit Inversion: Framing Losses in 24 hrs - Maintenance Limit: Framing Losses in 24 hrs - Service Limit: Integrated Digital Access: Satellite Link Delay: Slip Rate - Maintenance Limit (slips/24hr.):...

  • Page 8: Digital E And M Trunk Circuit Descriptor Assignment

    Digital E and M Trunk Circuit Descriptor Assignment Number: Call Collision Handling: AT&T Call Collision Handling: Ignore Far End Disconnect: Release Acknowledge Timer: Address Signalling: Disconnect Timer: Incoming Start Type: Dial Tone on Incoming Seize: Outpulse Delay Timer: Outgoing Start Type: Supervision Timer: Maximum Wink Timer: Minimum Wink Timer:...

  • Page 9: Digital Trunk Assignment

    Cabinet: Shelf: Slot: Circuit: Card Type: Trunk Number: Trunk Service Number: DTS Service Number: Circuit Descriptor Number: Interconnect Number: Example of ARS Programming on 3300 ICP/SX2000 Create Trunk Group Trunk Group Assignment Trunk Hunt Group Mode Number Terminal Circular Terminal...
  • Page 10 6102 6103 6104 6105 6106 6107 6108 6109 6110 7/4/2004 Page 10 of 22...

  • Page 11: Create Digit Modification Assignment

    Create Digit Modification Assignment in this example, we are using Digit Modification number 4, and there are no digits to absorb or to insert Digit Modification Assignment Digit Number of Modification Digits to Number Absorb Create Route Assignment in this example, we are using Route 4 Route Assignment Trunk Route...

  • Page 12: Sx200 With Isdn

    SX200 with ISDN Attach VCon IGC server to PRI card with straight through cable o Configure hardware for Line Termination. Please refer to SX200 Technician’s Handbook for more information. Program trunks o Please see Example of T1 PRI Programming on SX200 Use IMAT to configure PRI card for DMS250, user side Reset PRI card to allow new configuration to load Program ARS...
  • Page 13 Example of T1 PRI Programming on SX200 Refer to SX200 EL/ML Technicians Handbook , Programming a PRI, for System Configuration, Class of Service Options and System Options/System Timers. Form 13 Assign T1 E&M circuit descriptor to the ISDN trunk. 7/4/2004 Page 13 of 22...
  • Page 14 7/4/2004 Page 14 of 22...
  • Page 15 7/4/2004 Page 15 of 22...
  • Page 16 Define the incoming ISDN trunk as a Dial In trunk in form 15 7/4/2004 Page 16 of 22...
  • Page 17 Assign the ISDN trunks to a trunk group in Form 16 7/4/2004 Page 17 of 22...
  • Page 18 Select a T1 Link Descriptor for the ISDN trunks in form 42 7/4/2004 Page 18 of 22...
  • Page 19 7/4/2004 Page 19 of 22...

  • Page 20: Sx200 With T1/D4

    Assign the ISDN link descriptor to slot 6 and/or slot 8 on the PRI card bay, Form Form 44, Network Sync - To be determined by qualified Technician SX200 with T1/D4 Attach VCon IGC server to SX200 with cross over cable. Program trunks for T1/D4.

  • Page 21: T1 Crossover Cable Wiring Specifications [Rj45 Connector]

    T1 Crossover cable wiring Specifications [RJ45 Connector] Supplied with RemoteAbility system. Connector A Pin Connector B Pin 7/4/2004 Page 21 of 22...
  • Page 22 Addition & Corrections The change I had to make was with the ANI/DNIS insertion in digit mod with T1/D4 trunks The doc says above to insert **6135922122** The correct format for this string is : *ANI*DNIS* We used this at for fixed ANI at Pyramid: *3125551212*7900* For caller's ANI: *<E>*7900*...

Table of Contents