Hard Disk Drives - Asus Motherboard NCLV-D (A) Product Manual

3 . 3 . 3 . 3 . 3 . S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
These connectors are for the Serial ATA signal cables for Serial ATA

hard disk drives.

If you installed Serial ATA hard disk drives, you can create a RAID 0 or
RAID 1 configuration with the Adaptec
the onboard Intel
These connectors are set to S t a n d a r d I D E
S S S S S t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E mode, you can connect Serial ATA boot/data hard disk
t a n d a r d I D E
drives to these connectors. If you intend to create a Serial ATA RAID set
using these connectors, set the C o n f i g u r e S A T A A s
to [RAID]. See section "4.3.6 IDE Configuration" on page 4-15 for details.
NCLV-D
NCLV-D SATA connectors
I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A
• You must install Windows
Service Pack 1 before using Serial ATA hard disk drives. The Serial
ATA RAID feature (RAID 0/RAID 1) is available only if you are using
Windows
• Use only two Serial ATA RAID connectors for each RAID 0 or RAID 1
set.
• When using the connectors in S S S S S t a n d a r d I D E
primary (boot) hard disk drive to the SATA1 or SATA2 connector.
Refer to the table below for the recommended SATA hard disk drive
connections.
Serial ATA hard disk drive connection Serial ATA hard disk drive connection
Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection
C o n n e c t o r C o n n e c t o r C o n n e c t o r C o n n e c t o r C o n n e c t o r
S A T A 1 S A T A 1 S A T A 1
S A T A 1 S A T A 1
S A T A 2 S A T A 2 S A T A 2
S A T A 2 S A T A 2
A S U S N C L V - D ( A ) A S U S N C L V - D ( A )
A S U S N C L V - D ( A ) A S U S N C L V - D ( A ) A S U S N C L V - D ( A )
® 6300ESB integrated RAID controller.
S t a n d a r d I D E S t a n d a r d I D E
S t a n d a r d I D E S t a n d a r d I D E mode by default. In
C o n f i g u r e S A T A A s C o n f i g u r e S A T A A s C o n f i g u r e S A T A A s item in the BIOS C o n f i g u r e S A T A A s
RSATA_TXP2
RSATA_TXN2
RSATA_RXP2
RSATA_RXN2
RSATA_TXP1
RSATA_TXN1
RSATA_RXP1
RSATA_RXN1
® 2000 Service Pack 4 or the Windows
® 2000/XP.
S e t t i n g S e t t i n g S e t t i n g S e t t i n g S e t t i n g
M a s t e r M a s t e r M a s t e r
M a s t e r M a s t e r
S l a v e S l a v e S l a v e
S l a v e S l a v e
® HostRAID Technology through
SATA2
GND
GND
GND
SATA1
GND
GND
GND
t a n d a r d I D E mode, connect the t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E
U s e U s e U s e U s e U s e
B o o t d i s k B o o t d i s k B o o t d i s k
B o o t d i s k B o o t d i s k
D a t a d i s k D a t a d i s k D a t a d i s k
D a t a d i s k D a t a d i s k
® XP
2 - 2 7 2 - 2 7
2 - 2 7 2 - 2 7 2 - 2 7