Door Replacement And Adjustment - Electrolux E30MO65GSSA Service Manual

Hide thumbs Also See for E30MO65GSSA:
Table of Contents

Advertisement

6. Now, the control unit and frame assembly are
separated.
NOTE; . Before attaching a new key unit, remove remaining
adhesive on the control panel frame surfaces
completely with alcohol and so on.
THIRD DOOR SWITCH, DOOR SENSING SWITCH, PRIMARY INTERLOCK SWITCH AND MONITOR SWITCH REMOVAL
. Disconnect oven from power supply and remove outer
case.
2. Discharge high voltage capacitor.
3. Remove the control panel assembly, refer to "Control
Panel Removal".
4. Disconnect wire leads from each of the switches and
fuse holder.
5. Remove two (2) screws holding latch hook to oven
flange.
6. Remove latch hook assembly from oven flange.
7. Push outward on the one () stopper tabs holding each
of switches place.
8. Switch is now free.
chapter "Test Procedure" and Adjustment procedure.
THIRD DOOR SWITCH, DOOR SENSING SWITCH, PRIMARY
INTERLOCK SWITCH AND MONITOR SWITCH ADJUSTMENT
If the door sensing switch, third door switch, primary interlock
switch and monitor switch do not operate properly due to a
misadjustment, the following adjustment should be made.
. Loosen the two (2) screws holding latch hook to the oven
cavity front flange.
2. With door closed, adjust latch hook by moving it back
and forth, and up and down. In and out play of the door
allowed by the latch hook should be less than 0.5mm.
The vertical position of the latch hook should be adjusted
so that the door sensing switch and primary interlock
switch are activated with the door closed. The horizontal
position of the latch hook should be adjusted so that the
plungers of the monitor switch and the third door switch
are pressed with the door closed.
3. Secure the screws with washers firmly.
4. Check the all switches operation. If each switch has not
activated with the door closed, loosen the screw and
adjust it.
After adjustment, check the following.
. In and out play of door remains less than 0.5mm at the
REMOVAL
. Disconnect oven from power supply and remove the
outer case.
Remove turntable tray and turntable support from oven
cavity.
2. Remove three (3) screws holding lower oven hinge.
3. Remove the lower oven hinge from oven cavity bottom
flange.

DOOR REPLACEMENT AND ADJUSTMENT

2. When a attaching the key unit to the control panel
frame, adjust the lower edge and right edge of
the key unit to the correct position of the control
panel frame.
3. Stick the key unit firmly to the control panel frame
At this time switch lever will be free, do not lose it.
Re-install
. Re-install switch lever and each interlock switch in its
place. The primary interlock switch is in the lower position
and the door sensing switch and thir door switch are in
the upper position and the monitor switch is in the middle
position.
2. Re-connect wire leads to each switches and fuse
holder.
Refer to pictorial diagram.
3. Secure latch hook (with two (2) mounting screws) to
oven flange.
4. Make sure that the monitor switch is operating properly
and check continuity of the monitor circuit.
latched position.
2. The door sensing switch and primary interlock switch
interrupt the circuit before the door can be opened.
3. Monitor switch contacts close when door is opened.
4. The third door switch contacts open when the door is
opened.
5. Re-install outer case and check for microwave leakage
around door with an approved microwave survey meter.
(Refer to Microwave Measurement Procedure.)
LATCH
HEADS
DOOR OPEN
BUTTON
Figure C-4. Latch Switch Adjustments
4. Remove door assembly from upper oven hinge on the
oven.
5. Door assembly is now free.
Note: When the individual parts are replaced, refer to
"Door Disassembly".
6. On re-installing door, insert the upper oven hinge into
the door hinge pin. Then while holding door in place.
35
E30MO65GSSA
Refer to
LATCH HOOK
THIRD DOOR SWITCH
DOOR SENSING
SWITCH
MONITOR SWITCH
PRIMARY
INTERLOCK SWITCH
SWITCH LEVER
OPEN LEVER

Advertisement

Table of Contents
loading

Table of Contents