1. Manuals
  2. Brands
  3. Hunter Manuals
  4. Fan
  5. Hunter Ceiling fans
  6. Installation and operation manual

Hunter Ceiling Fans Installation And Operation Manual

Hide thumbs Also See for Ceiling Fans:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Instruction and Installation Manual, Operation & Installation Manual
Installation and Operation Manual
For Hunter Ceiling Fans
44204-01
5/30/2007

44203-01 05/30/2007

Advertisement

Table of Contents
loading

Related Manuals for Hunter Ceiling Fans

Summary of Contents for Hunter Ceiling Fans

  • Page 1 Installation and Operation Manual For Hunter Ceiling Fans 44204-01 5/30/2007 44203-01 05/30/2007...
  • Page 2 44204-01 05/30/2007...
  • Page 3 COngratulatIOns! Your new Hunter ceiling fan is an ad- Model Name ________________ dition to your home or office that will Catalog No. _________________ provide comfort and performance Attach Your Receipt for many years. This manual gives or a Copy of Serial No.

  • Page 4: Table Of Contents

    Step 4 - Wiring the Fan............................9 Step 5 - Installing the Canopy ...........................11 Step 6 - Assembling Fan Blades ........................12 Step 7 - Completing Your Installation ....................... 13 Operating Your Hunter Fan..........................15 Cleaning and Maintenance ..........................16 Troubleshooting ..............................17 44204-01...

  • Page 5: Important Information

    If you need help installing the fan, electrician. tions, and use only the your Hunter fan dealer can direct hardware supplied. • To reduce the risk of per- you to a licensed installer or elec- sonal injury, do not bend trician.

  • Page 6: Step 1 - Getting Ready

    step 1 - gettIng ready gatHeriNg tHe tools CHeCkiNg Your FaN parts Standard Mounting (Figure 1) hangs from the ceiling by a connector You need the following tools to in- Carefully unpack your fan parts to pipe (included), for ceilings 2.3 m stall the fan: avoid damage.

  • Page 7: Step 2 - Assembling The Fan

    step 2 - asseMblIng tHe Fan 1. Feed the wires and the steel ca- WarNiNg ble support from the fan through • Failure to complete the the canopy and the pipe. steps above properly could 2. Screw pipe into fan assembly until result in the fan falling.

  • Page 8: Step 3 - Hanging The Fan

    step 3 - HangIng tHe Fan Hang fan from the previously in- 4. Wrap the braided cable around down to the support brace. See stalled J-Hook or U-Hook. the support brace once creating Figure 3c. a complete circle. 7. Coil up the excess cable. Return seCuriNg FaN to seCoND- 5.

  • Page 9: Step 4 - Wiring The Fan

    step 4 - WIrIng tHe Fan green/yellow ground wire from WarNiNg WarNiNg the hanger. To reduce the risk of fire, elec- • To avoid possible electrical 3. Connect the blue neutral wire to trical shock, or motor damage, shock, before wiring fan, the blue wire from the fan.
  • Page 10 Figure 4 - WiriNg Diagram (Optional Line)� Wall Switch Wire For � Separate Control of Light Kit (Note: Wall switch � must be acceptable � as a general-use� Brown Power� switch.) Wires� In � Blue Ceiling Earth Connections:� � Connect Blk/Wht Wire from fan� to Wall Switch Wire for separate�...

  • Page 11: Step 5 - Installing The Canopy

    step 5 - InstallIng tHe CanOpy 1. Slide the canopy to where the top is within 2 mm of the ceiling. The canopy should not touch the ceiling or it will cause noise and possible wobble. Canopy 2. Insert and tighten the #6-32 canopy screw to hold the canopy in place.

  • Page 12: Step 6 - Assembling Fan Blades

    step 6 - asseMblIng Fan blades 1. Open the locking mechanism as 3. Close the locking mechanism se- shown in Figure 6a. curely feeling it lock into place. 2. Align the holes in the blade with the blade iron as shown in Fig- ure 6b.

  • Page 13: Step 7 - Completing Your Installation

    step 7 - COMpletIng yOur InstallatIOn 1. Install 60 Watt A-19 bulbs. 4. Place a pull chain clip over both caps. See Figure 7b. . Raise the shade until the knobs go through the holes. See Figure 7a. 3. Screw a cap shown in Figure 7a onto each knob.

  • Page 14: Completing Your Installation

    CompletiNg Your iNstallatioN 5. Remove the breakaway con- nectors and extra chain from the light and fan pull chains. See Figure 7d. 6. Thread the light and fan pull chains through the pull chain clips. See Figure 7d. 7. Re-connect the breakaway Pull Chain connectors and extra chain to the light and fan pull chains.

  • Page 15: Operating Your Hunter Fan

    OperatIng yOur Hunter Fan Control switches are identified by To change the direction of air the following symbols: flow, turn the fan off and let it come to a complete stop. Slide the reversing switch on the fan to the opposite position as shown in Figure 8c.

  • Page 16: Cleaning And Maintenance

    If you need parts or service as- soft brush or lint-free cloth should be blades should be cleaned with a sistance contact your Hunter Fan used to prevent scratching the fin- furniture polishing cloth. Occasion- retailer or visit our WEB site at: ish.

  • Page 17: Troubleshooting

    trOublesHOOtIng problem probable Cause solutioN Nothing happens; fan does not 1. Power turned off, fuse blown, or 1. Turn power on, replace fuse, or move. circuit breaker tripped. reset breaker. 2. Loose wire connections or wrong 2a. Loosen canopy, check all connec- connections.
  • Page 18 problem probable Cause solutioN Noisy operation (continued). 4. Using non-approved speed con- 4. Change to approved speed con- trol. trol. 5. Glass screwed loosely to fixture. 5. Hand-tighten the light fixture screws. Ensure that rubber noise isolators are installed. 6. Switch housing is loose. 6.

Table of Contents