Sony CA-905K Operation Manual page 38

Location and Function of Parts
Note
When the HDC-950 is used, be sure to attach the rear-
panel sticker (supplied with the CA-950L) to the rear
panel of the camera. For details regarding the sticker
position, see page 20.
1 POWER indicator
Lights as follows to show the power-supply status.
Green: Power is supplied to the camera.
Orange: Power is supplied to the camera, however
the VF PW button of the MSU-700 or RCP-700-
series unit is set to off and power is not supplied
to the viewfinder.
Not lit: Power is not supplied to the camera.
2 Video signal select buttons
Select the video signals (R, G, and B) displayed on the
viewfinder.
When no button is pressed, the following signals are
output:
When a monochrome viewfinder is used: The Y
signal is output to the viewfinder.
When a color veiwfinder is used: The R, G, and B
signals are output to the viewfinder, and a color
picture appears on the viewfinder.
3 H-POSI (horizontal position) control
Adjusts the horizontal position of the box cursor on the
viewfinder screen.
4 V-POSI (vertical position) control
Adjusts the vertical position of the box cursor on the
viewfinder screen.
5 WIDTH control
Adjusts the width of the box cursor on the veiwfinder
screen.
6 HEIGHT control
Adjusts the height of the box cursor on the veiwfinder
screen.
7 CURSOR STORE button
Press to store the size and position of the box cursor by
adjusting H-POSI, V-POSI, WIDTH, and HEIGHT
control.
Note
If the CURSOR ON button is not lit, the data cannot
be stored.
10 (E)
8 RET (return video) button
Push this button in to display in the viewfinder the
return video signal (2, 3, or 4) selected on the CA-950/
950P/570/570P or HDC-950. Push again to display the
video signal from the camera.
9 RET 1 (return video 1) button
Push this button to display the return video 1 signal on
the viewfinder screen. Push again to view the video
signal from the camera.
q; Back tally lamp
Lights when a red tally signal is supplied. When the
CALL button on the MSU-700 or RCP-700-series unit
is pressed, this lamp goes out if it is lit, and lights if it
is not lit.
Attach the supplied number plate to show the camera
number.
For details on attaching a number plate, see page 20.
qa CURSOR ON button
Press and light up this button to display the box cursor
on the viewfinder screen. Press this button again and
make the button go out, and the box cursor disappears.
qs CURSOR (cursor memory) 1, 2, and 3 buttons
Press one of these buttons with the CURSOR STORE
button blinking, and the size and position of the box
cursor displayed on the viewfinder screen is recalled or
stored. Three different box cursor settings can be
stored using these buttons.
You can recall the stored size and position of the box
cursor by merely pressing the corresponding button.
Note
When the CURSOR 1, 2, or 3 button is lit, the H-
POSI, V-POSI, WIDTH, and HEIGHT controls are
disabled.
qd PinP (Picture-in-Picture) switch
Used to display a small picture on a viewfinder screen.
POSITION: The position of the subscreen moves
each time you move the switch from ON to this
position.
ON: Enters PinP mode. When neither the RET 1 or
RET button is depressed, you can monitor the
camera's signal on the viewfinder screen and the
last selected return video signal on the small
picture. Press either the RET 1 or RET button to
switch the pictures on the viewfinder screen and
the small picture.
OFF: The subscreen does not appear.
Two other modes can also be selected.
For details, refer to the camera's System Manual.