GE C70 Instruction Manual page 541

APPENDIX B
Table B–10: MODBUS MEMORY MAP (Sheet 13 of 65)
ADDR REGISTER NAME
332C Syslog Server IP Address
332E Syslog Server Port Number
Security Supervisory (Read/Write Setting)
3331 Device Authentication Enable
3332 Supervisor Role Enable
3333 Lock Relay
3334 Factory Service Mode Enable
3335 Failed Authentication Alarm Enable
3336 Firmware Lock Alarm
3337 Settings Lock Alarm
3338 Bypass Access
333A Serial Inactivity Timeout
Security Command (Read/Write Command)
3350 Operator Logoff
3351 Engineer Logoff
3352 Administrator Logoff
3353 Clear Security Data
Security Reserved Modbus Registers (Read/Write)
3360 Address 0x3360 reserved for serial login (20 items)
3374 Address 0x3374 reserved for serial logout
Security Reserved Modbus Registers (Read Only)
3375 Address 0x3374 reserved for serial logout
Event Recorder (Read Only)
3400 Events Since Last Clear
3402 Number of Available Events
3404 Event Recorder Last Cleared Date
Event Recorder Commands (Read/Write Command)
3406 Event Recorder Clear Command
Neutral Current Unbalance Commands and Actual Values (Read/Write Unless Noted) (3 modules)
3410 Neutral Current Unbalance Automatic Setting Function
3411 Neutral Current Unbalance Apply Magnitude
3412 Neutral Current Unbalance Apply Angle
3413 60N Apply Magnitude Actual Value (Read Only)
3415 60N Apply Angle Actual Value (Read Only)
3417 ...Repeated for Neutral Current Unbalance 2
341E ...Repeated for Neutral Current Unbalance 3
Neutral Voltage Unbalance Commands and Actual Values (Read/Write Unless Noted) (3 modules)
3430 Neutral Voltage Unbalance Automatic Setting Function
3431 59NU XA/XB Ratio Actual Value (Read Only)
3433 Neutral Voltage Unbalance Auto-set XA/XB Ratio
3434 59NU XA/XC Ratio Actual Value (Read Only)
3436 Neutral Voltage Unbalance Auto-set XA/XC Ratio
3437 ...Repeated for Neutral Voltage Unbalance 2
343E ...Repeated for Neutral Voltage Unbalance 3
Phase Current Unbalance Commands and Actual Values (Read/Write Unless Noted) (3 modules)
3450 Phase Current Unbalance Automatic Setting Function
3451 Phase Current Unbalance Ka Actual Value (Read Only)
3453 Phase Current Unbalance Auto-set Ka
3454 Phase Current Unbalance Kb Actual Value (Read Only)
3456 Phase Current Unbalance Auto-set Kb
3457 Phase Current Unbalance Kc Actual Value (Read Only)
3459 Phase Current Unbalance Auto-set Kc
345A ...Repeated for Phase Current Unbalance 2
3464 ...Repeated for Phase Current Unbalance 3
GE Multilin
0 to 4294967295
0 to 4294967295
0 to 4294967295
0 to 4294967295
0 to 0.1500
0 to 9.9999
0 to 9.9999
–0.1000 to 0.1000
–0.1000 to 0.1000
–0.1000 to 0.1000
C70 Capacitor Bank Protection and Control System
RANGE UNITS STEP
--- 1
1 to 65535 --- 1
0 to 1 --- 1
0 to 1 --- 1
0 to 1 --- 1
0 to 1 --- 1
0 to 1 --- 1
0 to 1 --- 1
0 to 1 --- 1
0 to 3 --- 1
1 to 9999 --- 1
0 to 1 --- 1
0 to 1 --- 1
0 to 1 --- 1
0 to 1 --- 1
0 to 9999 --- 1
0 to 9999 --- 1
0 to 5 --- 1
--- 1
--- 1
--- 1
0 to 1 --- 1
0 to 2 --- 1
0 to 1 --- 1
0 to 1 --- 1
--- 0.0001
0 to 359 degrees 1
0 to 2 --- 1
--- 0.0001
0 to 1 --- 1
--- 0.0001
0 to 1 --- 1
0 to 2 --- 1
--- 0.0001
0 to 1 --- 1
--- 0.0001
0 to 1 --- 1
--- 0.0001
0 to 1 --- 1
B.4 MEMORY MAPPING
FORMAT DEFAULT
F003 0
F001 514
F126 1 (Yes)
F102 0 (Disabled)
F102 0 (Disabled)
F102 0 (Disabled)
F102 1 (Enabled)
F102 1 (Enabled)
F102 1 (Enabled)
F628 0 (Disabled)
F001 1
F126 0 (No)
F126 0 (No)
F126 0 (No)
F126 0 (No)
F001 3
F001 3
F617 3 (Engineer)
F003 0
F003 0
F050 0
F126 0 (No)
F092 0 (Disabled)
F126 0 (No)
F126 0 (No)
F003 0
F003 0
F092 0 (Disabled)
F003 0
F126 0 (No)
F003 0
F126 0 (No)
F092 0 (Disabled)
F004 0
F126 0 (No)
F004 0
F126 0 (No)
F004 0
F126 0 (No)
B-21
B