Step AS380 Series Manuals

Forward

3

Table of Contents

6

Chapter 1 General Knowledge of the Integrated Drive Controller

11

Scope of Application

11

Items in the Cases

11

Model Description

11

Integrated Drive Controller Nameplate

12

Notice Items for Safety

12

Operation Notice

14

Brake Resistor Selection

14

Absorber at the Output Side Prohibited

15

The Application Voltage of Integrated Device

15

Two-Phase Input Not Allowed

15

Altitude and Derated Application

16

Synchronous Sealing Star Delay

16

Low Voltage Directive Complies

16

Waste Disposal

17

Disposal of Capacitors

17

Disposal of Plastic Components

17

Chapter 2 Model and Specification

19

Model of Integrated Drive Controller

19

The Technical Specification of Integrated Drive Controller

19

The Installation Dimensions and Mass of the Integrated Drive Controller

21

Installation Instructions

23

Product Installation Location

23

Product Installation Positioning and Clearance Requirements

24

Chapter 3 Product Function

25

Function List

25

Elevator Operation Function Description and Setting Method

27

Standard Function Description

27

Optional Function Description

32

Chapter 4 Wiring of Elevator Integrated Drive Controller

35

The Connection between Integrated Drive Controller and Peripheral Equipments

36

For Typical Terminal Wiring Diagram of Elevator Integrated Drive Controller

36

Notice Items for Peripheral Equipments Connection

37

Power Supply

37

Breaker

37

AC Reactor at the Input Side

37

Interference Filter at the Input Side

37

Main Circuit Output Contactor

37

Interference Filters at the Output Side

37

AC Reactor at Output Side

37

DC Reactor

38

Elevator Integrated Drive Controller

38

The Cable Requirement of Hoist Way and Accompanying Cable Arrangement

38

Method of Wiring between Call Board and TXV+、TXV-、TXA+、TXA

39

Hoist Way Switch Position

40

Upper and Lower Leveling Inductor

41

Main Circuit Terminal Wiring

43

The Arrangement of Main Circuit Terminal

43

The Main Circuit Terminal Labeling and Function Description

43

Main Circuit Wire Specification

43

The Main Circuit Composition

46

The Detailed Description of Main Circuit Terminal Wiring

46

Anti-Interference Measures

50

The Specialized Noise Filter Connected at the Output Side

50

Main Circuit Wiring Arrangement

50

The Better Anti-Interference Measure

51

Relation between Wiring Length and Carrier Frequency

51

Wiring of Control Circuit Terminals

52

Layout of Control Circuit Terminals

52

Functional Description of Control Circuit Terminals

52

Dip Switch Setting Method

55

Wire Specification of Control Circuit

55

Main Extension Board SM.09I0/C Introduction

56

Notice Items for Control Circuit Terminal Wiring

58

The Wiring of PG Card Terminals

58

PG Card - Incremental ABZ 12V

58

PG Card - SIN/COS

61

PG Card - Incremental ABZ 5V

64

PG Card - Endat with Absolute Value

66

Precaution for PG Card Terminal Wiring

68

Chapter 5 Operator

69

The 7-Segment Display Operator

69

LED Indicator Light

69

Function Key

70

Operator Handling

71

Graphic Symbol of Number and Letter on LED Screen

85

LCD Handheld Operator

85

LCD Handheld Operator Introduction

85

Handheld Operator Connection Method

87

Handheld Operator Function

88

Introduction to Display Interface of LCD Hand-Held Operator

89

Chapter 6 Introduction to the Supporting Products

115

Car Top Control Board SM.02/H Introduction

116

Car Top Control Panel SM.02/H Outside View and Installation Dimension

116

Car Top Control Panel SM 02/H

117

Car Top Extension Board SM09I0/B Introduction

120

Car Top Extension Board SM09IO/B Outside View and Installation Dimension

120

Car Top Extension Board SM09IO/B Plug-In and Port Definition Introduction

121

Car Controller Panel SM.02/G Introduction

122

Car Controller Panel SM02/G Outside View and Installation Dimension

122

Car Control Board SM.02/G Plug-In and Port Definition Introduction

123

Instruction Control Board SM-03

126

Instruction Control Board SM-03 Outside View and Installation Dimension

126

Instruction Controller Board SM-03 Plug-In and Port Definition Introduction

126

Call & Display Control Board

128

Call &Display Control Board SM.04VR/K

128

Call& Display Control Board SM-04-HSC

129

Call & Display Control Board SM-04-VHL

130

Call & LCD Control Board SM-04-UL

132

Car Call & LCD Control Board SM-04-VL

134

In-Car SM-04-VL/B3 Outside View and Installation Dimension

136

Call& LED Display Control Panel SM-04-VSD

138

Call & LED Display SM-04-VRJ

140

Miscellaneous (a List of Display Codes)

141

SM.GC/C Board Introduction

143

System Structure

143

Basic Feature

144

Main Functions

145

Input of Call Button Signal and Control of Call Button Light

148

General Principle of Overall Deploy

148

Treatment in Special Situation

149

Instruction of Group Control Board (SM.GC/C)

150

Connection Method of Group Control System

157

Setting of Group Control Operation

157

Instruction of Group Control Program to Setup Parameters

158

Chapter 7 Parameter Table of Integrated Drive Controller

173

F Parameter List

173

Definition of Function Parameter

182

Chapter 8 Elevator Elevator Commissioning Guide

205

Check before Power on

208

Power on and Check

208

Confirmation before Power on

208

Checks after Power on

209

Configuration of System Basic Parameters and Self Study of Motor Parameters

209

Configuration of System Basic Parameters

209

Motor Parameter Self Study

211

Test Run of Slow Car

212

Inspection Operation of Engine Room and Preparations for Express Car

212

Car Top Inspection Operation

213

Check of CAN Communication Lines and Setting of 04 Board Address

214

Door Opening/Closing Adjustment

215

Hoist Way Self Study

215

Hoistway Self Study Method

215

Express Car Operation

216

Adjust Elevator Comfort

220

Factors Relating to Elevator Comfort in Operation

220

Leveling Adjustment

228

Method for Adjusting Pre-Load Weighing Compensation at Elevator Start

234

Use of DTZZ-III-DC-SC

236

Use of Non-DTZZ-III-DC-SC Weighing Device (F164 Set to 1, 2, 5 or 6) to Compensate or Adjust the Start

237

Simple Compensation by Using Light-Load and Heavy-Load Switch (F164 Set to 4)

238

The Adjustment of Other Function

239

Chapter 9 Faults and Solutions

241

The Fault Analysis of the Integrated Device Control System

241

Fault Analysis of Integrated Drive System

247

Chapter 10 Maintenance

253

Warranty

253

Product Checkup

254

Routine Inspection

254

Periodic Inspection

254

Appendix A EMC Installation Guide

257

A1 Noise Control

257

A1.1 Noise Type

257

A1.2 Transmission Path

257

A1.3 Basic Measures for Noise Suppression

258

A2 Requirements on Cable Laying

259

A2.1 Requirement on Cable Laying

259

A2.2 Requirements on Cable Size

260

A2.3 Requirements on Shielded Cable

260

A2.4 Requirements on Installation of Shielded Cable

260

A3 Grounding Requirements

260

A3.1 Grounding Method

260

A3.2 Precautions for Grounding Connection

261

A4 Install Surge Absorption Device

261

A5 Leakage Current and Countermeasures

262

A5.1 Ground Leakage Current

262

A5.2 Line-To-Line Leakage Current

262

A6 Suppression of Radiated Emission

263

A7 Guide for Use of Power Line Filter

264

A7.1 Functions of Power Line Filter

264

A7.2 Precautions for Installation of Power Line Filter

264

A8 EMC Installation Zoning

264

A9 Precautions for Electric Installation

265

A10 EMC Conformity

267

Appendix B Function Parameter, Fault List Summary

269

Function Parameter List

269

Fault Code and Analysis

283

Appendix C Inverter Complies with the Standards

297

Notice to Customers

299

STEP AS380 Series Manuals

STEP AS380 Series Instruction Manual (300 pages)

Table of Contents

STEP AS380 Series Instruction Manual (271 pages)

Table of Contents

Chapter One: General Knowledge of the Integrated Drive Controller

Scope of Application

Items in the Cases

Model Description

Integrated Drive Controller Nameplate

Notice Items for Safety

Operation Notice

Waste Disposal

Chapter Two: Model and Specification

Model of Integrated Drive Controller

The Technical Specification of Integrated Drive Controller

The Installation Dimensions and Mass of the Integrated Drive Controller

Installation Instructions

Chapter Three: Product Function

Function List

Elevator Operation Function Description and Setting Method

Chapter Four: Wiring of Elevator Integrated Drive Controller

The Connection between Integrated Drive Controller and Peripheral Equipments

Notice Items for Peripheral Equipments Connection

The Technical Requirements for Wire Arrangement of Peripheral Equipments of the Elevator Integrated Drive Controller

Main Circuit Terminal Wiring

Anti-Interference Measures

Wiring of Control Circuit Terminals

B.2 Fault Code and Analysis

The Wires of PG Card Terminal

Chapter Five ：Operator

LCD Handheld Operator

Chapter 6 Introduction to the Supporting Products

Car Top Control Board SM.02/H Introduction

Car Top Extension Board SM09I0/B Introduction

Car Controller Panel SM.02/G Introduction

Instruction Control Board SM-03

Call & Display Control Board

SM-GC Board Introduction

Chapter 7 Parameter Table of Integrated Drive Controller

F Parameter List

Definition of Function Parameter

Check before Power

Power on and Check

Configuration of System Basic Parameters and Self Study of Motor Parameters

Test Run of Slow Car

Hoist Way Self Study

Express Car Operation

Adjust Elevator Comfort

Leveling Adjustment

Method for Adjusting Pre-Load Weighing Compensation at Elevator Start

The Adjustment of Other Function

Chapter 9: Faults and Solutions

The Fault Analysis of the Integrated Device Control System

Fault Analysis of Integrated Drive System

Chapter 10: Maintenance

Warranty

Product Checkup

Routine Inspection

Periodic Inspection

Appendix Aemc Installation Guide

A1 Noise Control

A2 Requirements on Cable Laying

A3 Grounding Requirements

A4 Install Surge Absorption Device

A5 Leakage Current and Countermeasures

A6 Suppression of Radiated Emission

A7 Guide for Use of Power Line Filter

A8 EMC Installation Zoning

A9 Precautions for Electric Installation

A10 EMC Conformity

Appendix B Function Parameter, Fault List Summary

B.1 Function Parameter List

Notice to Customers

STEP AS380 Series Operation Manual (104 pages)

Related Products

STEP Categories