User Manuals: PANHANS 690|200 Sliding Table Saw

Manuals and User Guides for PANHANS 690|200 Sliding Table Saw. We have 1 PANHANS 690|200 Sliding Table Saw manual available for free PDF download: Operating Manual

PANHANS 690|200 Operating Manual (83 pages)

sliding

Brand: PANHANS | Category: Saw | Size: 5 MB

Table of Contents
2
Introduction
8
Legal Notice
8
Illustrations
8
Symbols
8
General Symbols
8
Figure 1: Saw Blade
8
Symbols in Safety Instructions
9
General
10
Intended Use
10
Target Group and Previous Experience
10
Requirements for the Operators
10
Accident Prevention
11
General Safety Regulations
11
Structure and Function
12
Standard Equipment
12
Special Equipment
13
Expandability
13
Safety
14
Basic Safety Instructions
14
Application Area and Intended Use
14
Modifications and Conversions to the Machine
14
Residual Risks
15
Observe the Environmental Protection Regulations
16
Organisational Measures
17
Personnel Selection and Qualification - Basic Duties
17
Safety Instructions for Specific Phases of Operation
17
Normal Operation
17
Special Work Within the Scope of Maintenance Work as Well as Troubleshooting in the Workflow
18
Safe Working Practices
18
Hazardous Areas on the Sliding Table Saw
20
Danger Zone Saw Blade
20
Danger Zones Around the Machine
20
Figure 2: Danger Zone Saw Blade
20
Figure 3: Danger Zones Around the Machine
20
Avoidance of Kickback Hazards
21
Use Fence and Saw Blade Guard
21
Never Work Without the Riving Knife
21
Rip Fence When Cutting Short Workpieces to Width
21
Figure 4: Cutting Short Workpieces to Width
21
Parallelism of the Rip Fence
22
Cutting off Small Pieces on the Rip Fence
22
Special Characteristics of Guards Made of Polycarbonate (Plexiglas)
22
Figure 5: Fixing the Deflector Wedge on the Table
22
Effect of Cooling Lubricants on Polycarbonate
23
Machine Data
23
Technical Specifications
23
Figure 6: Nameplate
23
Technical Characteristics
24
Emission Levels
25
Noise Emission Values
25
Dimensions
26
Working Areas
26
Dimensions (Front View)
26
Figure 7: Working Areas
26
Figure 8: Dimensions (Front View)
26
Dimensions (Top View)
27
Figure 9: Dimensions (Top View)
27
Installation and Connection
28
Check Delivery Conditions
28
Transport to the Installation Site
28
Figure 10: Machine Transport
28
Levelling with a Spirit Level
29
Procedure in the Normal Case
29
Procedure in the Exceptional Case
29
Figure 11: Levelling Screws at the Rear (Normal Case)
29
Figure 12: Front Levelling Screws (Exceptional Case)
29
Lashing on a Transport Vehicle
30
Temporary Storage
30
Figure 13: Lashing Points (4 X)
30
Connecting the Extraction Unit
31
Figure 14: Upper Suction Nozzle Diameter
31
Figure 15: Lower Suction Nozzle Diameter
31
Electrical Connection
32
Back-Up Fuses (On-Site)
32
Figure 16: Electrical Connection
32
Components & Controls
33
Figure 17: Components & Controls - Front View
33
Figure 18: Components & Controls - Top View
34
Mounting and Usage
35
Slide Table
35
Rip Fence
35
Figure 19: Slide Table Controls
35
Figure 20: Fitting the Rip Fence
35
Mounting the Cross Slide
36
Moving the Cross Slide
36
Figure 21: Cross Slide Mounting
36
Figure 22: Cross Slide Clamping
36
Figure 23: Moving the Cross Slide
36
Swivelling Saw Blade Guard
37
Change Saw Blade Guard
37
Figure 24: Swivel Arm for Saw Blade Guard
37
Figure 25: Fitting the Saw Blade Guard
37
Commissioning
38
Control Elements
38
Figure 26: Control Elements
38
Switching on
39
Switching off
39
Safety Equipment
39
Saw Blade Guard with Extraction
39
Safety Switches
39
Emergency Stop Switches
39
Pinch Protection Bar for the Rip Fence
39
Operating the Cross-Cut Fence
40
Setting Lengths > 1885 MM
40
Readjusting the Fence Rulers
40
Accessories for Mitres and Angles
40
Figure 27: Flip Stop with Measuring Scale and Magnifying Glass
40
Figure 28: Cross-Cut Fence Operating Elements
40
Figure 29: Fixing Screw
40
Operating the 7" Touchscreen Control
41
Start Screen
41
Status Window
41
Figure 30: Start Screen
41
Figure 31: Status Window
41
Set Language
42
Set Date and Time
42
Figure 32: Set Language
42
Figure 33: Set Date and Time
42
Operating the Rip Fence
43
Rip Fence Positioning
43
Figure 34: Rip Fence Positioning
43
Folding Away the Rip Fence
44
Calibrating the Rip Fence
44
Figure 35: Rip Fence in Folded Away Position
44
Figure 36: Calibrating the Rip Fence
44
Changing the Rip Fence Offset Value
45
Pinch Protection on the Rip Fence
45
Figure 37: Offset Value
45
Figure 38: Anti-Crush Bar
45
Operating the Scoring Saw
46
Positioning the Scoring Saw
46
Parking the Scoring Saw
46
Figure 39: Positioning the Scoring Saw
46
Figure 40: Parking the Scoring Saw
46
Calibrating the Scoring Saw
47
Discard Entry
47
Figure 41: Calibrating the Scoring Saw
47
Figure 42: Discard Entry
47
Speed Setting
48
Figure 43: Speed Setting - Loosen V-Belt
48
Figure 44: Speed Scheme
48
Saw Blade Adjustment
49
Saw Blade Height
49
Figure 45: Machine Setting Areas
49
Figure 46: Adjust Height
49
Tilting the Saw Blade (Angular Adjustment)
50
Angle Compensation Tool for Mitre Cuts
50
Figure 47: Adjust Angle
50
Figure 48: Angle Compensation Tool
50
Calibrate Saw Blade Height and Angle
51
Calibrate Angle
51
Calibrate Height
51
Figure 49: Angular Gap
51
Figure 50: Calibrate Angle
51
Figure 51: Calibrate Height
51
Figure 52: Set Saw Blade Height to 50.0 MM
51
Calibration with Calibration Device
52
Preparation
52
Calibration Procedure
52
Figure 53: Prepare Saw Blade Position
52
Figure 54: Calibration with Calibrator
52
Changing the Saw Blade
53
Remove Saw Blade
53
Figure 55: Remote Locking on the Slide Table
53
Figure 56: Safety Catch on the Slide Table
53
Figure 57: Fold Sawdust Flap Forwards
53
Figure 58: Saw Blade Flange
53
Insert Main Saw Blade
54
Riving Knife Setting
54
Figure 59: Riving Knife Setting (Symbolic Representation)
54
Optional Components
55
Tele-Digit Cross-Cut Fence
55
Features
55
Installation
55
Figure 60: Tele-Digit Cross-Cut Fence
55
Figure 61: Fixing Points on the Cross Slide
55
Tele-Digit Components
56
Digital Indicator
56
Length Measurement Switching
56
Calibrate Tele-Digit
56
Figure 62: Tele-Digit Components
56
Figure 63: Digital Indicator
56
Battery Change
57
Set & Change Reference Dimensions
57
Sleep-Mode
58
Fix Error Message "FULL
58
Figure 64: Error Message FULL
58
Rip Fence Left to the Saw Blade
59
Double-Sided Mitre Fences DSG-A and DSG-D
59
Figure 65: Rip Fence Mounted to the Left of the Saw Blade
59
Figure 66: Flip Stop (Left to the Saw Blade)
59
Figure 67: DSG-A (Analogue)
59
Figure 68: DSG-D (with Digital Indicator)
59
Cross-Cut & Mitre Fence Super Gehrfix I
60
Features
60
Figure 69: Super Gehrfix I
60
Super Gehrfix I Operation
61
Attach Cross-Cut Fence
61
Set Length > 1885 MM
61
Set Angle to 90 Degrees
61
Figure 70: Super Gehrfix I Overview
61
Figure 71: Attach Cross-Cut Fence
61
Setting Degrees & Intermediate Degrees
62
Cross-Cut & Mitre Fence Super Gehrfix II
62
Features
62
Figure 72: Super Gehrfix II
62
Components & Overview
63
Calibrate Super Gehrfix II
63
Attach Cross-Cut Fence
63
Set Length > 1885 MM
63
Set Angle to 90 Degrees
63
Figure 73: Super Gehrfix I Overview
63
Setting Degrees & Intermediate Degrees
64
Changing Parameters of the Digital Indicator
64
Auxiliary Mitre Fence for Super Gehrfix
65
Operating the Auxiliary Mitre Fence
65
Standard Mitre Fence
65
Figure 74: Auxiliary Mitre Fence
65
Figure 75: Operating the Auxiliary Mitre Fence
65
Figure 76: Standard Mitre Fence
65
Power Feeder 76
66
Mounting the Power Feeder
66
Figure 77: Power Feeder 76
66
Figure 78: Mounting the Power Feeder
66
Adjustable Scoring Saw Blade "Quickstep
67
Setting the Scoring Width
67
Changing the Scoring Saw Blade
67
Figure 79: Quickstep Setting Mechanism for Scoring Saw Blade
67
Figure 80: Quickstep Quick-Release Screw
68
Manual Scoring Unit 1750
69
Figure 81: Saw Blade Flange of the Scoring Saw
69
Figure 82: Safety Catch of the Sawdust Flap
69
Adjusting the Manual Scoring Saw
70
Spraying System
70
Special Features When Using a Spraying System
70
Calibration Device
70
Figure 83: Setting Wheels for Scoring Saw
70
Figure 84: Calibrator "Zeromaster
70
Laser Cut-Position Indicator
71
Trimming with Laser Beam
71
Special Requirements for Use
71
Figure 85: Laser Cut-Position Indicator
71
Figure 86: Trimming with Laser Beam
71
Swivel-Away Device for the Cross Slide
72
Attaching the Swivel Arm to the Cross Slide
72
Reattaching the Cross Slide
72
Figure 87: Position and Mount Swivel Arm
72
Figure 88: Swivel Away Cross Slide
72
Figure 89: Final Parking Position
72
Troubleshooting
73
Fault Messages on the Touchscreen
74
Figure 90: Error Message 1
74
Figure 91: Error Message 2
74
Figure 92: Error Message 3
74
Figure 93: Error Message 4
74
Figure 94: Error Message 5
75
Figure 95: Error Message 6
75
Figure 96: Error Message 7
75
Figure 97: Error Message 8
75
Figure 98: Error Message 9
75
Figure 99: Error Message 10
75
Figure 100: Error Message 11
76
Figure 101: Error Message 12
76
Figure 102: Error Message 13
76
Figure 103: Error Message 14
76
Figure 104: Error Message 15
76
Figure 105: Error Message 16
76
Retightening / Changing the V-Belt
77
Figure 106: Error Message 17
77
Figure 107: Error Message 18
77
Figure 108: V-Belt Tightness
77
Maintenance and Inspection
78
Lubrication Guide
78
Figure 109: Lubrication Points on the Height Adjustment and Rip Fence Spindle
78
Options and Accessories
79
Sawing Units
79
Optional Fence Systems
79
Slide Table and Additional Supports
80
Support Systems
80
Special Accessories
81
Disassembly and Scrapping
82
EU - Declaration of Conformity
83

PANHANS Categories

Saw Power Tool Planer Control Unit Controller

More PANHANS Manuals

User Manuals: PANHANS 690|200 Sliding Table Saw

PANHANS 690|200 Operating Manual (83 pages)

Table of Contents

Related Products

PANHANS Categories