PANHANS 100 Manuals

Manuals and User Guides for PANHANS 100. We have 1 PANHANS 100 manual available for free PDF download: Operating Manual

PANHANS 100 Operating Manual (77 pages)

Sliding Table Saw

Brand: PANHANS | Category: Saw | Size: 4.42 MB

Table of Contents
2
Introduction
8
Legal Notice
8
Illustrations
8
Symbols
8
General Symbols
8
Figure 1: Saw Blade
8
Symbols in Safety Instructions
9
General
10
Intended Use
10
Target Group and Previous Experience
10
Requirements for the Operators
10
Accident Prevention
11
General Safety Regulations
11
Structure and Function
12
Standard Equipment
12
Special Equipment
13
Expandability
13
Safety
14
Basic Safety Instructions
14
Application Area and Intended Use
14
Modifications and Conversions to the Machine
14
Residual Risks
15
Observe the Environmental Protection Regulations
16
Organisational Measures
17
Personnel Selection and Qualification - Basic Duties
17
Safety Instructions for Specific Phases of Operation
17
Normal Operation
17
Special Work Within the Scope of Maintenance Work as Well as Troubleshooting in the Workflow
18
Safe Working Practices
18
Hazardous Areas on the Sliding Table Saw
20
Danger Zone Saw Blade
20
Danger Zones Around the Machine
20
Figure 2: Danger Zone Saw Blade
20
Figure 3: Danger Zones Around the Machine
20
Avoidance of Kickback Hazards
21
Use Fence and Saw Blade Guard
21
Never Work Without the Riving Knife
21
Rip Fence When Cutting Short Workpieces to Width
21
Figure 4: Cutting Short Workpieces to Width
21
Parallelism of the Rip Fence
22
Cutting off Small Pieces on the Rip Fence
22
Figure 5: Fixing the Deflector Wedge on the Table
22
Special Characteristics of Guards Made of Polycarbonate (Plexiglas)
23
Effect of Cooling Lubricants on Polycarbonate
23
Machine Data
23
Technical Specifications
23
Figure 6: Nameplate
23
Technical Characteristics
24
Emission Levels
25
Noise Emission Values
25
Dimensions
26
Working Areas
26
Dimensions (Front View)
26
Dimensions (Top View)
26
Figure 7: Working Areas
26
Figure 8: Dimensions (Front View)
26
Figure 9: Dimensions (Top View)
27
Installation and Connection
28
Check Delivery Conditions
28
Transport to the Installation Site
28
Figure 10: Machine Transport
28
Levelling with a Spirit Level
29
Procedure in the Normal Case
29
Procedure in the Exceptional Case
29
Figure 11: Levelling Screws at the Rear (Normal Case)
29
Figure 12: Front Levelling Screws (Exceptional Case)
29
Lashing on a Transport Vehicle
30
Temporary Storage
30
Figure 13: Lashing Points (4 X)
30
Connecting the Extraction Unit
31
Figure 14: Upper Suction Nozzle Diameter
31
Figure 15: Lower Suction Nozzle Diameter
31
Electrical Connection
32
Back-Up Fuses (On-Site)
32
Figure 16: Electrical Connection
32
Components & Controls
33
Figure 17: Components & Controls - Front View
33
Figure 18: Components & Controls - Top View
34
Mounting and Usage
35
Slide Table
35
Rip Fence
35
Figure 19: Slide Table Controls
35
Figure 20: Rip Fence
35
Operating the Rip Fence
36
Figure 21: Fitting the Rip Fence
36
Figure 22: Operating the Rip Fence
36
Mounting the Cross Slide
37
Moving the Cross Slide
37
Figure 23: Cross Slide Mounting
37
Figure 24: Cross Slide Clamping
37
Figure 25: Moving the Cross Slide
37
Swivelling Saw Blade Guard
38
Change Saw Blade Guard
38
Figure 26: Swivel Arm for Saw Blade Guard
38
Figure 27: Fitting the Saw Blade Guard
38
Commissioning
39
Control Elements
39
Switching on
39
Switching off
39
Figure 28: Control Elements
39
Safety Equipment
40
Saw Blade Guard with Extraction
40
Safety Switches
40
Emergency Stop Switches
40
Operating the Cross-Cut Fence
41
Setting Lengths > 1885 MM
41
Readjusting the Fence Rulers
41
Accessories for Mitres and Angles
41
Figure 29: Flip Stop with Measuring Scale and Magnifying Glass
41
Figure 30: Cross-Cut Fence Operating Elements
41
Figure 31: Fixing Screw
41
Operating the 4.7" Touch Display
42
Start Screen
42
Status Window
42
Figure 32: Start Screen
42
Figure 33: Status Window
42
Language Settings
43
Machine Overview
43
Saw Blade Calibration
43
Figure 34: Language Settings
43
Figure 35: Machine Overview - Current Positions and Speed
43
Calibrate Height
44
Figure 36: Saw Blade Height 50 MM
44
Figure 37: Calibrate Height
44
Figure 38: Adopt Calibration Value for Height
44
Calibrate Angle
45
Figure 39: Angular Gap
45
Figure 40: Calibrate Angle
45
Figure 41: Adopt Calibration Value for Angle
45
Date and Time (from Software Version 1.9)
46
Speed Setting
46
Figure 42: Set Date and Time
46
Figure 43: Speed Setting - Loosen V-Belt
46
Figure 44: Speed Scheme
46
Changing the Saw Blade
47
Remove Saw Blade
47
Figure 45: Remote Locking on the Slide Table
47
Figure 46: Safety Catch on the Slide Table
47
Figure 47: Fold Sawdust Flap Forwards
47
Figure 48: Saw Blade Flange
47
Insert Main Saw Blade
48
Riving Knife Setting
48
Figure 49: Riving Knife Setting (Symbolic Representation)
48
Optional Components
49
Tele-Digit Cross-Cut Fence
49
Features
49
Installation
49
Figure 50: Tele-Digit Cross-Cut Fence
49
Figure 51: Fixing Points on the Cross Slide
49
Tele-Digit Components
50
Digital Indicator
50
Length Measurement Switching
50
Calibrate Tele-Digit
50
Figure 52: Tele-Digit Components
50
Figure 53: Digital Indicator
50
Battery Change
51
Set & Change Reference Dimensions
51
Sleep-Mode
52
Fix Error Message "FULL
52
Figure 54: Error Message FULL
52
Rip Fence Left to the Saw Blade
53
Double-Sided Mitre Fences DSG-A and DSG-D
53
Figure 55: Rip Fence Mounted to the Left of the Saw Blade
53
Figure 56: Flip Stop (Left to the Saw Blade)
53
Figure 57: DSG-A (Analogue)
53
Figure 58: DSG-D (with Digital Indicator)
53
Cross-Cut & Mitre Fence Super Gehrfix I
54
Features
54
Figure 59: Super Gehrfix I
54
Super Gehrfix I Operation
55
Attach Cross-Cut Fence
55
Set Length > 1885 MM
55
Set Angle to 90 Degrees
55
Figure 60: Super Gehrfix I Overview
55
Figure 61: Attach Cross-Cut Fence
55
Setting Degrees & Intermediate Degrees
56
Cross-Cut & Mitre Fence Super Gehrfix II
56
Features
56
Figure 62: Super Gehrfix II
56
Components & Overview
57
Calibrate Super Gehrfix II
57
Attach Cross-Cut Fence
57
Set Length > 1885 MM
57
Set Angle to 90 Degrees
57
Figure 63: Super Gehrfix I Overview
57
Setting Degrees & Intermediate Degrees
58
Changing Parameters of the Digital Indicator
58
Auxiliary Mitre Fence for Super Gehrfix
59
Operating the Auxiliary Mitre Fence
59
Standard Mitre Fence
59
Figure 64: Auxiliary Mitre Fence
59
Figure 65: Operating the Auxiliary Mitre Fence
59
Figure 66: Standard Mitre Fence
59
Digit PAB - Absolute Measuring System for the Rip Fence
60
Digit-PAB Features
60
Digit PAB - Operation
60
Digit PAB - Rip Fence Capacities
60
Figure 67: Digit PAB
60
Figure 68: Rip Fence with Digit-PAB
60
Power Feeder 76
61
Mounting the Power Feeder
61
Figure 69: Power Feeder 76
61
Figure 70: Mounting the Power Feeder
61
Adjustable Scoring Saw Blade "Quickstep
62
Setting the Scoring Width
62
Changing the Scoring Saw Blade
62
Figure 71: Quickstep Setting Mechanism for Scoring Saw Blade
62
Figure 72: Quickstep Quick-Release Screw
63
Manual Scoring Unit 1750
64
Figure 73: Saw Blade Flange of the Scoring Saw
64
Figure 74: Safety Catch of the Sawdust Flap
64
Adjusting the Manual Scoring Saw
65
Spraying System
65
Special Features When Using a Spraying System
65
Figure 75: Setting Wheels for Scoring Saw
65
Laser Cut-Position Indicator
66
Trimming with Laser Beam
66
Special Requirements for Use
66
Figure 76: Laser Cut-Position Indicator
66
Figure 77: Trimming with Laser Beam
66
Swivel-Away Device for the Cross Slide
67
Attaching the Swivel Arm to the Cross Slide
67
Reattaching the Cross Slide
67
Figure 78: Position and Mount Swivel Arm
67
Figure 79: Swivel Away Cross Slide
67
Figure 80: Final Parking Position
67
Troubleshooting
68
Fault Messages on the Touchscreen
69
Figure 81: Error Message 1
69
Figure 82: Error Message 2
69
Figure 83: Error Message 3
69
Figure 84: Error Message 4
69
Figure 85: Error Message 5
69
Figure 86: Error Message 6
69
Figure 87: Error Message 7
69
Retightening / Changing the V-Belt
70
Figure 88: V-Belt Tightness
70
Maintenance and Inspection
71
Lubrication Guide
71
Figure 89: Lubrication Points on the Height Adjustment
71
Options and Accessories
72
Sawing Units
72
Machine Operation
72
Optional Fence Systems
72
Slide Table and Additional Supports
74
Support Systems
74
Special Accessories
75
Disassembly and Scrapping
76
EU - Declaration of Conformity
77

PANHANS Categories

Saw Power Tool Planer Control Unit Controller

More PANHANS Manuals

PANHANS 100 Manuals

PANHANS 100 Operating Manual (77 pages)

Table of Contents

Related Products

PANHANS Categories