FLENDER N-BIPEX BWN Manuals

Manuals and User Guides for FLENDER N-BIPEX BWN. We have 1 FLENDER N-BIPEX BWN manual available for free PDF download: Assembly And Operating Instructions Manual

FLENDER N-BIPEX BWN Assembly And Operating Instructions Manual (68 pages)

Brand: FLENDER | Category: Industrial Equipment | Size: 0.98 MB

Table of Contents
3
Introduction
11
Legal Information
11
About These Instructions
12
Text Attributes
12
Copyright
13
Safety Instructions
15
General Information
15
Table 2-1 General Warnings
16
Intended Use
17
Safety Instructions for a Coupling for Use in Potentially Explosive Atmospheres
17
Marking
17
Conditions of Use
18
Table 2-2 Temperature Classes (TX) for Explosive Atmospheres as a Result of Gases, Vapours or Mists
18
Table 2-3 Maximum Surface Temperature (TX) for an Explosive Atmosphere as a Result of Dust/Air Mixtures
18
General Warning Notices
19
Description
21
Figure 3-1 BWN Type
21
Figure 3-2 BWT Type
22
Figure 3-3 BNT Type
22
Application Planning
23
Transport of the Coupling
23
Storage of the Coupling
23
Figure 4-1 Transport Symbols
23
Table 4-1 Types of Preservative Agents for Long-Term Storage
24
Assembly
25
Preparatory Work
25
Milling the Finished Bore
26
Table 5-1 Recommended Assigned Fits for Bores with Parallel Key Connection
26
Milling the Parallel Keyway
27
Machining an Axial Locking Mechanism
27
Figure 5-1 Tolerances for the Finished Bore in Coupling Part 1/2 (1 or 2)
27
Table 5-2 Tapped Hole, Tightening Torque and Width A/F
28
Figure 5-2 Diameter and Axial Position of the Threaded Hole in the Hub
28
Balancing the Coupling
29
Figure 5-3 Position of the Balancing Bore for Single-Plane Balancing
29
Assembling the Coupling
30
Installing Coupling Part 1/2 (1 or 2)
30
Figure 5-4 Position of the Balancing Bore for Two-Plane Balancing
30
Assembling Coupling Part 3 (3) or 4 (4)
31
Aligning the Coupling
32
Purpose of Alignment
32
Possible Misalignment
33
Axial Misalignment
33
Angular Misalignment
33
Radial Misalignment
33
Figure 5-5 Possible Misalignment
33
Commissioning
35
Operation
37
Normal Operation of the Coupling
37
Faults - Causes and Rectification
37
Procedure in the Event of Malfunctions
37
Identifying the Fault Cause
37
Possible Faults
38
Possible Causes
39
Unsuitable Coupling
39
Assembly-Related Causes
39
Table 7-1 Table of Faults
39
Maintenance-Related Causes
40
Specific Installation-Related and Maintenance-Related Causes
40
Correcting Faults
40
Replacing Wearing Parts
40
Correcting the Changed Alignment
40
Servicing
43
Maintenance Intervals
43
Table 8-1 Maintenance Intervals
43
Maximum Permissible Torsional Backlash
44
Replacing Wearing Parts
44
Table 8-2 Maximum Permissible Torsional Backlash
44
Figure 8-1 Markings for Calculating the Torsional Backlash
44
Removing Coupling Part 1/2 (1 or 2)
45
Removing Coupling Part 3 (3) or 4 (4)
45
Service and Support
47
Contact
47
Disposal
49
Spare Parts
51
Ordering Spare Parts
51
Spare Parts Drawing and Spare Parts List
52
Type BWN
52
Type BWT
52
Table 11-1 Spare Parts List for Type BWN
52
Figure 11-1 Replacement Parts Drawing for BWN Type
52
Figure 11-2 Replacement Parts Drawing for BWT Type
52
Type BNT
53
Table 11-2 Replacement Parts List for BWT Type
53
Table 11-3 Spare Parts List for Type BNT
53
Figure 11-3 Spare Parts Drawing for Type BNT
53
Technical Data
55
Speeds, Geometry Data and Weights
55
BWN Type
55
Figure A-1 BWN Type
55
BWT Type
56
Table A-1 Speed, Geometry Data and Weights for BWN Type
56
Figure A-2 BWT Type
56
Table A-2 Speed, Geometry Data and Weights for BWT Type
57
BNT Type
58
Figure A-3 BNT Type
58
Flat Groove in TAPER Clamping Bushes (101), (102)
59
Shaft Misalignment Values During Operation
59
Table A-3 Speed, Geometry Data and Weights for BNT Type
59
Table A-4 Flat Groove in TAPER Clamping Bushes
59
Figure A-4 Flat Groove in TAPER Clamping Bushes
59
Table A-5 Correction Factor
60
Table A-6 Maximum Permissible Shaft Misalignment Values During Operation for Cam Rings (50) with
60
Table A-7 Maximum Permissible Shaft Misalignment Values During Operation for Cam Rings (50) with
61
Table A-8 Maximum Permissible Shaft Misalignment Values During Operation for Cam Rings (50) with Hardness 64 Shore a
61
Tightening Torques and Widths A/F
62
Tightening Procedure
62
Table A-9 Tightening Torques and Widths A/F of Bolts for the Taperclamping Bushes (101 or 102)
62
Table A-10 Tightening Procedure
62
Cam Rings
63
Use and Storage of the Cam Rings
63
N-BIPEX Cam Ring (50)
63
Table A-11 N-BIPEX Cam Ring
63
Declaration of Conformity
65

FLENDER Categories

Industrial Equipment Accessories Tools Sander Adapter

More FLENDER Manuals

FLENDER N-BIPEX BWN Manuals

FLENDER N-BIPEX BWN Assembly And Operating Instructions Manual (68 pages)

Table of Contents

Related Products

FLENDER Categories