Sign In
Upload
Manuals
Brands
EngA Manuals
Controller
C-TRAC2
User Manuals: EngA C-TRAC2 Cooling Controller
Manuals and User Guides for EngA C-TRAC2 Cooling Controller. We have
1
EngA C-TRAC2 Cooling Controller manual available for free PDF download: Installation, Operation And Maintenance Manual
EngA C-TRAC2 Installation, Operation And Maintenance Manual (35 pages)
COOLING CONTROLLER
Brand:
EngA
| Category:
Controller
| Size: 0 MB
Table of Contents
Table of Contents
2
Application
6
Service
6
General
6
IV. Wiring
7
Wiring
7
Heat Output
7
System Timings
7
Dip Switches and Pots
7
Pots and Dip Switch Chart
9
Status Lights
10
Heating Control Mode
10
Cooling Control Mode
10
Compressor Ambient Closed
10
Internal Timer
10
Fan Control and Low Limit
10
Control Start-Up and Operating Strategies
10
Heat Output
10
Heat Ramp Used on the Original C-TRAC
10
IX. Status Lights
10
Heat Ramp Used on the Revised C-TRAC2.1
11
Hot Water and Steam Heating
11
Simulate a Call for Maximum Heat
11
Economizer Control
11
Minimum Pot Position
11
BMS Minimum Position Reset
12
Cooling
13
Compressor Ambient Lockout
13
Cooling Delays
13
To Simulate a Call for Full Cooling
13
Burner Operation
13
Temperature Control - General Overview
14
Discharge Temperature Calculation
14
Sensors and Set-Points
14
The Master Set-Points
14
XIII. Temperature Control – General Overview
14
The Optional Reset Inputs
15
Night Heat
15
Induced Voltage on Remote Control Wiring
15
Night Heat Thermostats
15
Night Setback
15
Room Reset Thermostat Options
16
Options
16
Reset of the Discharge Set-Point from Other Controls
16
TE 6100-960 Set-Point Controller Connections
16
Option 1 - Combination Sensor/Set-Point
16
Option 2 - Remote Discharge Set-Point with Separate Discharge Sensor
16
Option 3 - Room Sensor Only
17
Multiple Room Sensors
17
TE 6100-960 Room or R/A Set-Point/Sensor C/W Dipswitch 3 "On
17
Ma or 0-10 VDC BMS Reset Signal
18
Calibration for BMS Configuration
18
Calibration Method 1
19
Calibration Method 2
19
Calculated Set-Point
19
Discharge Temperature Sensing
19
Set-Point Calibration
19
TE 6100-960 Johnson Controls Set-Point/Sensor Approximate Resistance
20
Sensor Resistance Chart for te 6100-960 and te 6000-960
20
Discharge Temperature Calibration Methods
20
Discharge Calibration Method 1
20
A C-Trac2.1 Manual
20
Discharge Calibration Method 2
21
Discharge Calibration Method 3
21
Discharge Calibration Method 4
21
Room or Return Air Temperature Calibration Methods
21
Room Calibration Method 1
21
Room Calibration Method 2
21
Ambient Reset Calibration
21
Suggested Settings Re Hunting Problems
22
LOCK-UP - Radio Frequency Interference
23
C-Trac2.1 Set up Sheet
24
Trouble Shooting
25
To Simulate a Full Call for Cooling
25
To Simulate a Full Call for Heat
25
C-TRAC2.1 Internal Operating Rules
25
C-TRAC2.1 Set-Point Calculation
25
Is the C-TRAC2.1 Properly Configured
26
Does Control Cycle through an Excessive Number of Operating Modes
26
Voltage Noise
26
Heating Trouble Shooting
26
Overheating
26
No Heat
27
Discharge too Cool
27
Hunting (External Causes)
27
H-Trac
27
G-Trac, Djm2.1
27
DJM2 Slaving from C-TRAC
28
G-Trac2
28
For Direct C-TRAC Control of the G-TRAC-2
28
Sensor Location
28
Mixed Air Dampers
28
Possible C-TRAC2.1 Adjustments to Reduce Hunting
28
Economizer Trouble Shooting
29
To 10 VDC Motors
29
Motors Wired to R, B, and W Terminals
29
Economizer Not Opening
29
Minimum Position Is Open too Much
30
Mechanical Cooling Trouble Shooting
30
Cooling Not Running
30
Advertisement
Advertisement
Related Products
EngA CenCon
EngA CRD C-TRAC3
EngA CRD-200 C-TRAC3
EngA Base
EngA DJM3
EngA ENGINEERED AIR DJM2.4
EngA G-TRAC 1.1
EngA Categories
Controller
Monitor
Gas Heater
Heat Pump
Heating System
More EngA Manuals
Login
Sign In
OR
Sign in with Facebook
Sign in with Google
Upload manual
Upload from disk
Upload from URL