CapstanAG PinPoint II Manuals

Manuals and User Guides for CapstanAG PinPoint II. We have 3 CapstanAG PinPoint II manuals available for free PDF download: Operator's Manual, Operator And Maintenance Manual, Quick Reference Information

CapstanAG PinPoint II Operator's Manual (144 pages)

Spray Application

Brand: CapstanAG | Category: Controller | Size: 6 MB

Table of Contents
3
Chapter 1: Introduction

7
- This Manual
  7
- System Identification
  7
Chapter 2: Safety

9
- Signal Words
  9
- Emergency Safety
  9
- Personal Protective Equipment
  10
- Safety Signs
  10
- Pressurized Fluid Lines
  10
- Chemical Safety
  10
- Battery Safety
  10
Chapter 3: Warranty

11
- Limited Warranty
  11
Chapter 4: System Installation

13
Chapter 5: System Setup

31
Chapter 6: Operation

75
- Operate in Automatic Pressure Control (AUTO) Mode
  75
- Manual Mode Operation
  76
- Spray Without the Pinpoint ™ II System
  77
  - Spray through the Capstanag Nozzle Valves
    77
  - Spray through Alternate Valve Bodies
    77
- Nozzle Display
  78
- Overlap Control
  79
- Mapping
  79
- Capmaps ™ -Boundary Mapping
  83
- Install the Capmaps ™ Software
  83
- Overlap Distance
  89
  - Change the Overlap Distance
    89
- Flowmeter Signal
  90
  - Change the Flowmeter Settings-Synchro ™ Mode
    90
  - Change the Flowmeter Settings-Sharpshooter Mode
    90
- Turn Compensation
  91
- Counters
  91
  - Gallon Counters
    92
  - Acre Counters
    92
  - Reset the Counters
    92
- Alarm
  92
- Nozzle Speed Ranges
  93
  - Metric Nozzle Speed Ranges
    93
  - US Measurements Nozzle Speed Ranges
    99
Chapter 7: Maintenance

105
- Service the System
  105
  - Jump Start, Weld On, or Charge the Machine
    105
- Inspect the System
  105
- Clean the System
  105
- Storage of the System
  105
  - Winterize for Storage
    105
- Recommended Guidelines for Maintenance/Service
  106
- Baseline Evaluation Process
  106
- Strainers and Screens
  106
- Nozzle Valves
  107
  - Clean the Nozzle Valve(S)
    108
  - Plunger Seal Inspection
    110
- Update Pinpoint ™ II Software
  111
Chapter 8: Troubleshooting

113
- Troubleshooting Charts
  113
- Interchange the Components
  121
- Fuses
  121
- Coil Assembly Test
  121
- Circuit Breaker
  122
- Battery Voltage Test
  123
- Do a Check of the System Load Capacity
  124
- VCM Voltage Test
  125
- Boom Shutoff Signal Test
  126
- Power to the Pressure Sensor Input Test
  127
- Pressure Sensor Signal Test
  128
- Technical Bulletin
  129
Chapter 9: Schematics

131
- Connector Pin Identification
  131
  - Capview Connector Pinout
    133
  - VCM Connector Pinout
    134

CapstanAG PinPoint II Operator And Maintenance Manual (78 pages)

For N-Ject NH3

Brand: CapstanAG | Category: Controller | Size: 5 MB

Table of Contents
3
Safety
5
- Signal Words
  5
- Safety Signs
  5
- Pressurized Fluid Lines
  6
- Personal Protective Equipment
  6
- Battery Safety
  6
- Chemical Safety
  6
- Emergency Safety
  6
Introduction
7
- This Manual
  7
- System Identification
  7
Operation
9
- Capview Button Descriptions
  9
- Start up Procedure
  10
- Shut down Procedure
  10
- Operate in Automatic Control (AUTO) Mode
  10
- Nozzle Display
  11
- Overlap Control
  12
- Mapping
  13
  - Download Maps
    13
- Overlap Distance
  14
  - Change the Overlap Distance
    14
- Flow Meter Signal
  14
- Turn Compensation
  15
- Counters
  16
  - Gallon Counters
    16
  - Acre Counters
    16
  - Reset the Counters
    16
- Alarm
  16
- Vent and Drain the N-Ject™ System
  17
Maintenance
19
- Service the System
  19
- Clean the System
  19
- Inspect the System
  19
- Jump Start, Weld On, or Charge the Machine
  19
- Storage of the System
  19
- Clean the Y-Strainer
  20
- Clean the Inlet Strainer
  20
- Nozzle Valves
  21
  - Clean the Nozzle Valve(S)
    21
  - Inspect the Plunger Seal
    22
Troubleshooting
23
- Capview System Error Chart
  23
- Over and under Application
  24
  - Rate Controller - under Application
    26
- Rate Controller - over Application
  26
- Rate Controller - Rate Instability
  26
- Liquid Level Sensor Alarm
  27
- Recommended Guidelines
  28
- Baseline Evaluation Process
  28
- Interchange the Components
  28
- Fuses
  29
- Coil Test
  29
- Circuit Breaker
  30
- Check the Battery Voltage
  30
- Check the System Load Capacity
  31
- Connector Pin Identification
  31
- Check the VCM Voltage
  34
- Check the Boom Shutoff Signal
  34
- Test the Pressure Sensor Signal
  35
- Check the Power to the Pressure Sensor Input
  36
- Liquid Level Sensor
  37
  - Test the Sensor Voltages
    37
Warranty
39
Schematics
41
- Manifold Schematics
  41
Installation and Setup
45
Index
75

CapstanAG PinPoint II Quick Reference Information (2 pages)

Brand: CapstanAG | Category: Control Systems | Size: 0 MB

CapstanAG Categories

Control Systems Farm Equipment Controller

Monitor Paint Sprayer

More CapstanAG Manuals

CapstanAG PinPoint II Manuals

CapstanAG PinPoint II Operator's Manual (144 pages)

Table of Contents

Chapter 1: Introduction

Chapter 2: Safety

Chapter 3: Warranty

Chapter 4: System Installation

Chapter 5: System Setup

Chapter 6: Operation

Chapter 7: Maintenance

Chapter 8: Troubleshooting

Chapter 9: Schematics

CapstanAG PinPoint II Operator And Maintenance Manual (78 pages)

Table of Contents

CapstanAG PinPoint II Quick Reference Information (2 pages)

Table of Contents

Related Products

CapstanAG Categories