Sign In
Upload
Manuals
Brands
Aetechron Manuals
Amplifier
7548
Aetechron 7548 DC-enabled Amplifier Manuals
Manuals and User Guides for Aetechron 7548 DC-enabled Amplifier. We have
1
Aetechron 7548 DC-enabled Amplifier manual available for free PDF download: Operator's Manual
Aetechron 7548 Operator's Manual (40 pages)
Single-Channel Industrial Amplifiers for Demanding, High-Power Systems
Brand:
Aetechron
| Category:
Amplifier
| Size: 2 MB
Table of Contents
Declaration of Conformity
4
Table of Contents
7
1 Introduction
9
Features
9
Figure 1.1 - 7548 Front Panel
9
2 Amplifier Setup
10
Safety First
10
Unpacking
10
Installation
10
Connecting the Load
11
Figure 2.1 - Connecting the Load
11
Figure 2.2 - Close-Up of the Output Terminal Resistor
11
Connecting the Input Signal
12
Figure 2.3 - Close-Up of SIM Card
12
Figure 2.4 - Wiring for Unbalanced or Balanced Input Connector
12
Connecting the AC Supply
13
Start-Up Procedure
13
Figure 2.5 - 208V 3-Phase AC Mains Wiring
13
Figure 2.6 - 380/400/415V 3-Phase AC Mains Wiring
13
3 Amplifier Operation
14
Front-Panel Controls & Display
14
Figure 3.1 - Front Panel Controls and Display
14
Input Buttons
14
Front-Panel Indicators
15
Figure 3.2 - Front Panel Indicators
15
Figure 3.3 - Main Status Indicators for Stand-Alone Amplifiers
15
Navigation Buttons
15
Figure 3.4 - Fault Status Indicators for Stand-Alone Amplifiers
16
Figure 3.5 - Main Status Indicators for Multi-Amplifier Systems
17
Figure 3.6 - Fault Status Indicators for Multi-Amplifier Systems
18
Back-Panel Controls and Connectors
19
Figure 3.7 - Back Panel Controls and Connectors
19
4 Advanced Configuration
20
Factory Defaults
20
Accessing the Main Board
20
Configuration Settings Located on the Main Board
20
Figure 4.1 - Master or Slave Setting
21
Figure 4.2 - Gain Trim Control
21
Figure 4.3 - Controlled-Voltage or Controlled-Current Mode Setting
21
Figure 4.4 - Compensation Setting
22
Figure 4.5 - Ready/Run Mode or Standby Mode on Power-Up Setting
22
Figure 4.6 - Standby Mode on Overtemp Setting
22
Figure 4.7 - Standby Mode on Overload Setting
22
Adjusting the Bi-Level Power Supply Switch
23
Figure 4.8 - Bi-Level Power Switch Location
23
5 Applications
24
Remote Status and Control Using the SIM Interlock I/O Connector
24
Figure 5.1 - Remote Status and Control Pinouts
24
Figure 5.2 - Remote Run/Standby Monitor
24
Figure 5.3 - Remote Status and Reset Schematic
25
Figure 5.4 - Remote Enable/Standby
26
Figure 5.5 - Remote Voltage Monitoring
27
Figure 5.6 - Remote Current Monitoring
27
Controlled Current Operation
28
Figure 5.7 - Remote Current Monitoring, Alternate Method
28
Figure 5.8 - Input to Output Comparison, Controlled-Voltage Operation
28
Figure 5.9 - Input to Output Comparison, Controlled-Current Operation
29
Figure 5.10 - Factory-Installed Default RC Network
29
Figure 5.11 - Custom Compensation Location
31
Figure 5.12 - Compensation Effects on Waveform
31
Multi-Amplifier Systems
32
Figure 5.13 - Square Wave Showing a Decrease in R Is Required
32
Figure 5.14 - Square Wave Showing an Increase in R Is Required
32
Figure 5.15 - Square Wave Showing an Increase in C Is Required
32
6 Maintenance
34
Clean Amplifier Filter and Grills
34
7 Troubleshooting
35
Introduction & Precautions
35
Visual Inspection
35
Figure 7.1 - +VCC and -VCC Point Locations
35
Figure 7.2 - Amplifier Cover Removed for Inspection
35
No Signal
36
No Leds Illuminated or no Fans
36
Overvoltage Warning Message
36
Standby LED Remains Illuminated
36
Figure 7.3 - Fuse F1 Location
36
Figure 7.4 - Interlock I/O Connector
36
Amplifier Overheats (over Temp Fault Condition)
37
Figure 7.5 - +TEMP and -TEMP Test Point Locations
37
Fault LED Is Illuminated
38
Factory Service
38
8 Specifications
39
Advertisement
Advertisement
Related Products
Aetechron 7794
Aetechron 7796
Aetechron 7228
Aetechron 7114
Aetechron 7548RLY
Aetechron 7796RLY
Aetechron 7212
Aetechron 7234
Aetechron 7220 Series
Aetechron 7224
Aetechron Categories
Amplifier
Transformer
Test Equipment
Relays
Inverter
More Aetechron Manuals
Login
Sign In
OR
Sign in with Facebook
Sign in with Google
Upload manual
Upload from disk
Upload from URL