AT&T CL82203 Quick Start Manual

Quick start guide
CL82203/CL82303/CL82353/CL82403/CL82453/CL82553
This quick start guide provides you with basic instructions only.
For more complete instructions, refer to your Abridged user's
manual provided in the package, or see the online Complete
user's manual at www.telephones.att.com/manuals.
Telephone base installation
Plug the power adapter
If you have
into an electrical outlet not
DSL high-speed
controlled by a wall switch.
Internet service,
a DSL filter
(not included)
is required. The
DSL filter must
be plugged into
the telephone
Plug the other
wall jack.
end of the
telephone line
cord into a
telephone jack
or a DSL filter.
Raise the
antenna.
Route the
cords through
the slots.
Plug the power cord
and telephone line
cord into the jacks.
Caution: Use only the power adapters provided with this product. To obtain a replacement,
www.telephones.att.com
visit our website at
1 (866) 288-4268
In Canada, dial .
Battery installation
Install the battery as shown below. Charge your handsets before initial use.
The battery is fully charged after 10 hours of continuous charging.
1 2
1. Plug the battery 2. Align the cover
connector securely flat against
into the socket inside the battery
the handset battery compartment,
compartment. Insert the then slide it
supplied battery with upwards until it
the label THIS SIDE UP clicks into place.
facing up as indicated.
Use only the supplied rechargeable battery or replacement battery (model BT183342).
Quick reference guide
q
CID/VOLUME
• Show caller ID history.
• Scroll down in menus.
• Move cursor to the left when
entering names or numbers.
• Decrease listening volume when
on a call, or decrease message
playback volume.
Charger installation
�EDIAL/PAUSE
Plug the power adapter
• Press repeatedly to view the last
into an electrical outlet
10 numbers dialed.
not controlled by
• Press and hold to insert a dialing
a wall switch.
pause while entering numbers.
PHONE/FLASH
• Make or answer a call.
• Answer a call waiting call during
a call.
1
• Press repeatedly to add or remove
1 in front of the call log entry
before dialing or saving it
to the directory.
• Press and hold to set or dial your
voicemail number.
/ a>A
TONE
• Press to switch to tone dialing
temporarily during a call if you
have pulse service.
• While entering names, press to
change the next letter to upper or
lower case.
/SPEA�E� SPEA�E�
Switch between the speakerphone
1 (800) 222-3111
or call .
and handset.
Handset
side view
3
/ANSWE� ON/OFF
Turn the built-in answering
system on or off.
3. Charge the handset by
Message counter
placing it face forward
Shows the number of
in the telephone base messages or other answering
system information.
or charger.
/�EPEAT
• Repeat a message.
• Press twice to play the
previous message.
Handset
pDI�/VOLUME
• Show directory entries.
• Scroll up in menus.
• Move cursor to the right when
entering names or numbers.
• Increase listening volume when
on a call, or increase message
playback volume.
MENU/SELECT
• Show the menu.
• Select an item or save an entry
or setting while in the menu.
OFF/CANCEL
• Hang up a call.
• Press to cancel an operation,
back up to the previous menu, or
exit the menu display,
or press and hold to return to
idle mode.
• Press and hold in idle mode to
erase the missed call indicator.
QUIET # (pound key)
• Press repeatedly to display other
dialing options when reviewing a
caller ID log entry.
• Press and hold to enter the
QUIET mode setting screen, or to
deactivate QUIET mode.
EQ
Change the audio quality to best
suit your hearing.
MUTE/DELETE
• Mute the microphone during a call.
• Delete the displayed entry while in the directory, call
log or redial list.
• Delete digits or characters when using the dialing keys.
PUSH TO TAL�
• Press to initiate a one-to-one
or one-to-group broadcast.
• Press and hold to broadcast
to a group of handsets.
X/DELETE
• Delete the message
Telephone base
currently playing.
• Press twice to delete all old
messages when in idle mode.
q/VOL- and p/VOL+
• Adjust the listening volume
during message playback.
• Adjust the base ringer
volume when in idle mode.
/S�IP
Skip to the next message.
/PLAY/STOP
Start or stop message
playback.
Initial settings
We recommend you program your telephone system before use.
The following are a few examples of common features to set before using the
telephone. Refer to the Handset settings and Answering system settings in
the Abridged user's manual or the online Complete user's manual for detailed
instructions on setting all telephone features.
Set date/time
Set the date/time before using the answering system.
1. MENU -> q or p -> Set date/time -> SELECT.
2. Enter the month, day and year using the dialing keys -> SELECT.
3. Enter the hour and minute using the dialing keys.
4. q or p to choose AM or PM -> SELECT.
Record your own announcement
Your outgoing announcement plays when calls are answered by the answering
system. You can use the preset announcement to answer calls, or replace it
with your own recorded announcement.
1. MENU -> q or p -> Answering sys -> SELECT.
2. SELECT to select Announcement.
3. q or p -> �ecord annc -> SELECT.
4. Facing the handset, record your announcement and press 5 to end recording.
Number of rings
You can set the answering system to answer an incoming call after two, three,
four, five or six rings, or toll saver. If you choose toll saver, the answering
system answers a call after two rings if you have new messages, or after four
rings when there are no new messages.
If you want the built-in answering system instead of the voicemail to answer a
call, you should set the answering system to answer a call at least two rings
before the voicemail is set to answer. Contact your telephone service provider
for information on your voicemail settings.
MENU -> q or p -> Answering sys -> SELECT.
1.
2. q or p -> Ans sys setup -> SELECT.
3. q or p -> # of rings -> SELECT.
4. q or p -> choose among 2, 3, 4, 5, 6 or Toll saver -> SELECT.
Handset ringer volume
You can set the ringer volume level to one of the six levels or turn the
ringer off.
1. MENU -> q or p -> �ingers -> SELECT.
2. SELECT to select �inger volume.
3. q or p to choose the desired level -> SELECT.
Reset language to English
If you have accidentally changed the screen display language and want to
switch it back to English, follow the steps below.
• MENU in idle mode-> enter 364#.