AT&T CL82107 Quick Start Manual

CL82107/CL82207/CL82307/
This quick start guide provides you
CL82357/CL82407/CL82507
with basic instructions only. For
more complete instructions, refer
to your Abridged user's manual
provided in the package, or see the
online Complete user's manual at
www.telephones.att.com/manuals.
Quick start guide
Part lists
Ì
1 for CL82207
Ì
2 for CL82307/
CL82357
Ì
3 for CL82407
Ì
4 for CL82507
Install
Telephone base
Notes:
Ì
Plug one end of the telephone line cord into a telephone jack or a DSL
filter.
Ì
If you have DSL high-speed Internet service, a DSL filter (not included)
is required.
Charger
Caution: Use only the power adapter(s) provided with this product.
To obtain a replacement, visit our website at
www.telephones.att.com 1 (800) 222-3111
or call
1 (866) 288-4268
Canada, dial
.
Battery
Install the battery, as shown below. Charge your handset(s)
before initial use. The battery is fully charged after ten hours
of continuous charging.
THIS SIDE UP /
CE CÔTÉ VERS LE HAUT
Ì
1 for CL82107
Ì
2 for CL82207
Ì
3 for CL82307/
CL82357
Ì
4 for CL82407
Ì
5 for CL82507
CL82107/CL82207/CL82307/
CL82357/CL82407/CL82507
Quick start guide
Caution: Use only the supplied rechargeable battery or replacement
battery (model BT183342/BT283342).
Overview
Handset
Ì
CHARGE light On when the handset is charging in
the telephone base or charger.
Ì
PUSH TO TALK Press to initiate a one-to-one or
one-to-group broadcast.
Ì
Press and hold to broadcast to a
group of system devices.
Ì
REDIAL Press repeatedly to view the last
PAUSE
ten numbers dialed.
Ì
While entering numbers, press and
. In
hold to insert a dialing pause.
Ì
When the handset is not in use,
MENU
SELECT
press to show the menu.
Ì
While in the menu, press to select
an item or save an entry or setting.
Ì
Press to make or answer a call.
FLASH
Ì
PHONE During a call, press to answer an
incoming call when you receive a
call waiting alert.
Ì
During a call, press to hang up.
CANCEL
Ì
While in a menu, press to cancel an
OFF
operation, back up to the previous
menu, or exit the menu display; or
press and hold this button to exit
to idle mode.
Ì
1 Press and hold to set or dial your
voicemail number.
Ì
Press to switch to tone dialing
temporarily during a call if you
have pulse service.
Ì
While entering names, press to
change the next letter to upper or
lower case.
Ì
Press and hold to enter the
QUIET mode setting screen, or to
deactivate QUIET mode.
Ì
Press to make or answer a call
using the speakerphone.
Ì
During a call, press to mute the
MUTE
DELETE
microphone.
Ì
Press to delete digit or character.
Ì
CALL BLOCK Press to block the incoming call
when the telephone is ringing.
Ì
When on a call, press to block the
call.
Ì
When the handset is not in use,
press to show the call block menu.
We recommend you program your telephone system
before use. The following are a few examples of common
features to set before using the telephone. Refer to the
Handset settings and Answering system settings in
the Abridged user's manual or the online Complete user's
manual for detailed instructions on setting all telephone
features.
Date and time
Note: Set the date/time before using the answering system.
1. ->
2. Enter the month, day and year using the dialing keys ->
SELECT.
3. Enter the hour and minute using the dialing keys.
4. or
Basic answering system setup via
voice guide
Handset
You can follow the voice guide to record your own
announcement, set the number of rings and set the
Ì
DIR Press DIR to show directory entries
message alert tone.
when the handset is not in use.
1. ->
Ì
Press to scroll up or down while in
2. or
menus.
3. Set up the answering system by inputting the designated
Ì
Press to increase or decrease the
numbers, as instructed.
listening volume when on a call.
Ì
CID Press CID to show caller ID log
Record your own announcement
when the handset is not in use.
Your outgoing announcement plays when calls are
answered by the answering system. You can use the preset
announcement to answer calls, or replace it with your own
Telephone base
recorded announcement.
Ì
IN USE indicator On when the telephone is in 1. ->
use, or when the answering
2.
system is answering an
3.
incoming call.
4. Facing the handset, record your announcement and press
Ì
Flashes when another
5 to end recording.
telephone is in use on the same
line.
Number of rings
Ì
Shows the number of
message
messages.
You can set the answering system to answer an incoming
counter
call after 2, 3, 4, 5, or 6 rings. You can also select toll saver. If
X / DELETE Ì
Press to delete the message
you choose toll saver, the answering system answers a call
currently playing.
after two rings when you have new messages, and after four
Ì
Press twice to delete all old
rings when there are no new messages. This enables you to
messages when the telephone
check for new messages and avoid paying unnecessary long
is not in use.
distance charges if you are calling from out of your local
area.
Ì
/ SKIP Press to skip a message.
If you want the built-in answering system instead of the
Ì
Press to start or stop message
/ PLAY/STOP
voicemail to answer a call, you should set the answering
playback.
system to answer a call at least two rings before the
Ì
/ REPEAT Press to repeat a message.
voicemail is set to answer. Contact your telephone service
Ì
Press twice to play the previous provider for information on your voicemail settings.
message.
1. ->
Ì
Press to turn the built-in
/ ANS ON/OFF
2. or
answering system on or off.
3. or
Ì
While the phone is idle, press to
FIND HS 4. or
page all handsets.
SELECT.
Ì
While in idle mode, press to
/ -VOLUME+ /
adjust the base ringer volume.
Ringer volume
Ì
During message playback,
press to adjust the listening
You can set the ringer volume level to one of the six levels, or
volume.
turn the ringer off.
1. ->
2.
3. or
Basic initial settings
or -> Set date/time -> SELECT.
to choose AM or PM -> SELECT.
or -> Answering sys -> SELECT.
-> Voice guide -> SELECT.
or -> Answering sys -> SELECT.
to select Announcement.
to select Record annc.
or -> Answering sys -> SELECT.
-> Ans sys setup -> SELECT.
-> # of rings -> SELECT.
to choose among 2, 3, 4, 5, 6, or Toll saver ->
or -> Ringers -> SELECT.
to select Ringer volume.
to choose the desire level -> SELECT.