Fuel System; Transporting; Storage; Preparing For Storage - Honda HRC216HXA Owner's Manual

FUEL SYSTEM

Refueling
Honda recommends using a No-Spill
This engine is certified to operate on unleaded gasoline with a pump
octane rating of 86 or higher.
If the fuel level is low, refuel in a well-ventilated area with the engine
stopped. If the engine has been running, allow it to cool first. Never
refuel the engine inside a building where gasoline fumes can reach
flames or sparks.
You may use regular unleaded gasoline containing no more than 10%
ethanol (E10) or 5% methanol by volume. In addition, methanol must
contain cosolvents and corrosion inhibitors. Use of fuels with content
of ethanol or methanol greater than shown above may cause starting
and/or performance problems. It may also damage metal, rubber, and
plastic parts of the fuel system. Engine damage or performance
problems that result from using a fuel with percentages of ethanol or
methanol greater than shown above are not covered by warranty.
If your equipment will be used on an infrequent or intermittent basis,
please refer to the fuel section of the STORAGE chapter (page 15) for
additional information regarding fuel deterioration.
B
WARNING
Gasoline is highly flammable and explosive.
You can be burned or seriously injured when handling fuel.
• Stop the engine and keep heat, sparks, and flame away.
• Handle fuel only outdoors.
• Wipe up spills immediately.
Never use stale or contaminated gasoline or an oil/gasoline mixture.
Avoid getting dirt or water in the fuel tank.
To refuel, remove the fuel
tank cap and fill the tank
with gasoline to the fuel
upper level indicator.
Refuel carefully to avoid
spilling fuel. Do not overfill;
fuel should be below the
upper level indicator in the
filler neck.
After refueling, tighten the
fuel tank cap until it clicks.
Move the mower at least
10 feet (3 meters) away
from the fueling source and
site before starting the
engine.
NOTICE
Fuel can damage paint and plastic. Be careful not to spill fuel when
filling your fuel tank. Damage caused by spilled fuel is not covered by
the DISTRIBUTOR'S LIMITED WARRANTY (page 20).
14
®
gas can (page 19).
FUEL UPPER FUEL FILLER
LEVEL INDICATOR NECK

TRANSPORTING

If the engine has been running, allow it to cool for at least 15 minutes
before loading the mower on the transport vehicle. A hot engine and
exhaust system can burn you and ignite some materials.
1. Turn the fuel valve to the OFF position. This will prevent carburetor
flooding and reduce the possibility of fuel leakage.
2. If installed, remove the grass bag.
If a suitable loading ramp is not available, two people should lift the
mower on and off the transport vehicle while holding the mower level.
Position the mower so all four wheels are on the bed of the transport
vehicle. Tie the mower down with rope or straps and block the wheels.
Keep the tie-down rope or straps away from the controls, adjustment
levers, cables, and the carburetor.

STORAGE

PREPARING FOR STORAGE

Proper storage preparation is essential for keeping your lawn mower
trouble free and looking good. The following steps will help keep rust
and corrosion from impairing your lawn mower's function and
appearance, and will make the engine easier to start when you use
the lawn mower again.
Cleaning
Engine
Wash the engine by hand and be careful to prevent water from
entering the air cleaner.
NOTICE
Using a garden hose or pressure washing equipment can force water
into the air cleaner. Water in the air cleaner will soak the paper filter
and can enter the carburetor or engine cylinder, causing damage.
Water contacting a hot engine can cause damage. If the engine has
been running, allow it to cool for at least half an hour before washing.
Mower Deck
Wash the lawn mower, including the underside of the mower deck.
If using a garden hose or pressure washing equipment to clean the
mower deck, be careful to avoid getting water into controls and
cables, or anywhere near the engine air cleaner or muffler opening.
Before washing the underside of the mower deck, be sure the fuel
valve is in the OFF position. Disconnect the spark plug cap. Rest the
mower on its right side so the air cleaner side is up. This will help
prevent fuel leakage and hard starting due to carburetor flooding.
Wear heavy gloves to protect your hands from the blades.
Grass Bag
Remove the bag from the mower and wash it with a garden hose or
pressure washing equipment. Allow the bag to dry completely before
storage.
Drying
1. After washing the lawn mower, wipe dry all accessible surfaces.
2. With the mower in an upright position, start the engine outdoors,
engage the blade control lever, and let the engine run until it
reaches normal operating temperature to evaporate any water
remaining on the engine.
3. While the engine is running, operate the blade control lever 4 or 5
times to expel water from the blade control mechanism. Allow the
blade to spin for several minutes to ensure that no water remains.
Stop the engine and allow it to cool.