Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for GarageAce S3
Summary of Contents for GarageAce S3
- Page 1 GARAGE DOOR OPENER OWNER’S MANUAL...
- Page 2 Features Locking door after power failure: An advanced technology with patent. If power failure occurs while the door is opening, the door can be released by pulling the clutch down, moving the door to the closed position manually, the door can then be locked.
- Page 3 Resistance protection: the opener will check and set the force of the running resistant protection which ensures the opener has high sensitivity and adapts the running resistance fluctuation automatically even after the door is in service for a long time, manual adjustment is unnecessary.
-
Page 4: Table Of Contents
Contents 1. Required tool list 2. Important safety instructions 3. Opener installation 3.1 Important installation instructions 3.2 Installation sketch map 3.3 Sectional rail assembling 3.4 Opener installation 3.5 Hoisting opener 3.6 Installation of door opening limit 4. Adjustment instructions 4.1 Ready status 4.2 Operation instructions 4.3 Adjusting methods 4.4 Advanced setting... -
Page 5: Required Tool List
Required tool list Name Specification Quantity Electric drill Ladder Mobile wrench or socket wrench 1 set Measuring tape Screw driver - Flat 2.5×100mm Screw driver - Flat 6×200mm Screw driver - Philips 6×200mm Pincer 10#、12# Allen key Important safety instructions WARNING –... -
Page 6: Opener Installation
Opener Installation 3.1. Important installation instructions In order to reduce the risk of serious injuries or death, please read and follow all instructions provided! Install only on a properly balanced door. An improperly balanced door has the potential to inflict severe injury. Have a qualified service person make repairs to cables, spring assemblies, and other hardware before installing the opener! Remove all ropes and remove or make inoperative all locks connected to the garage door before installing opener! -
Page 7: Installation Sketch Map
3.2. Installation sketch map As figure 1 shows the completed installation： Figure 1 3.3. Sectional rail assembling 3.3.1. Rail connection Take out the sectional rails (as shown in Figure 2), put them in line on a clean and flat floor (as shown in Figure 3). -
Page 8: Opener Installation
3.4. Opener installation 3.4.1. Opener connection Assemble opener as shown in Figure 7, fasten four anti-loose screws(provided) M8 × 16. Figure 7 3.4.2. C-type slide rail assembly and clutch cord fixing As shown in Figure 8, fasten the clutch rod together with small head screws(provided) M6x20, ensure that it is solid and reliable. -
Page 9: Installation Of Door Opening Limit
3.5.2. Hoisting the opener As in Fig12 showing, connect the rail to the front bracket on the wall, lift the motor side of the opener enough to make the rail level. Adjust the length of L1, and connect the perforated angle with bolts. -
Page 10: Adjustment Instructions
Adjustment instructions Open the cover as shown in Fig16 showing before adjusting. 4.1. Ready status After switching on the power, the LED lights will turn on for 2 seconds and off. Then the opener enters ready status, the LED flashes slowly showing the door body’s position. - Page 11 4.3.4. Open force setting Press the “P” button until LED shows as Fig20. Pressing “+” and “-” will adjust the opening load force by adjusting the value from 0 to 9. After adjusting, press “P” to confirm. If you needn’t change the value, just Figure 20 press “P”...
-
Page 12: Advanced Setting
4.4. Advanced setting In the ready status, press the “P” button until LED shows the picture shows as Fig25, then release the button. 4.4.1. Transmitter setting When the LED turns on as Fig 25. Press “+” or “-“ to set between 0 and 2. “0” stands for two button control;... -
Page 13: Installation Instruction For Accessories
Accessory installation 6.1. Photo beam installation Photo beam is an infrared protection system. If anything interrupts the infrared beam when the door is closing, the opener will stop working instantly and will move back to full opening position automatically. 6.1.1. Locating photo beam As Fig. -
Page 14: Maintenance And Repair
Maintenance and repair Please inspect the automatic reversal and the door balance monthly, and adjust it if necessary. Technical data Max. output power: 200 W Max. lifting force: 600 N Opening and closing speed: 160 mm/s Light: 12 V（high light LED） Motor: DC 24 V Remote control distance: 30 m Remote frequency: 433.92 MHz... -
Page 15: Trouble Shooting
Trouble shooting Trouble Reason Solution ●Switch on the power, ●Opener is not powered on The motor doesn’t work and inspect “ POWER” socket ●Fuse on main control board is has no display on LED ●Change fuse to the same damaged type fuse. - Page 16 Distributed in New Zealand by Newfield Group PO Box 11303, Christchurch, New Zealand www.garageace.co.nz 0800 600 789...